In case I want to initialize the weights between the input layer and hidden layer of a neural network with GA?
What population should I choose?
Thank you,
Do you have any application Area in mind?
If by population, you meant data set, there are many publicly available data sets that you can start with:
http://archive.ics.uci.edu/ml/index.php
The initialization between input layer and hidden layer is generated by weights and biais, so the chromosom represente the concatenation of weights and biais. Thé fitness function is the mean square error
I hope the response is useful
Hey! I'm looking for "Adaptive sliding mode control based neural network MATLAB code" Any suggestions please. Regards,
02 March 2019 6,907 4 View
Hello everyone, In this control diagram, Genetic-Algorithm (GA) is used to optimize the Radial Basis Function Neural Network (RBFNN) parameters. My question is: do we need to optimize and train...
01 February 2019 8,879 2 View
who worked on Vibration Suppression of a Cantilever Beam with Neural Network PID controller? thank you
02 March 2018 2,078 2 View
who is familiar with training Neural Network with PSO ?
01 February 2018 9,328 3 View
I have to write a MATLAB code for training artificial neural network (ANN) using particle swarm optimization(PSO).In the case, I choose the SISO system attached here, 1) How could I define the...
06 July 2017 8,256 1 View
I am facing some difficulties in processing the multidimensional wavelet network. Is there an expert to discuss it ?
31 December 2016 9,759 6 View
06 July 2016 9,937 4 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
Is there a powerful system for the security of the systems distributed on IoT systems?
02 March 2021 3,858 10 View
Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...
01 March 2021 6,200 3 View
I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...
28 February 2021 6,477 1 View
I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...
27 February 2021 8,128 1 View
Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...
26 February 2021 6,253 3 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...
26 February 2021 1,100 5 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View
Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...
25 February 2021 3,443 4 View