If my Sample gives more OD than my Control DPPH, what can I do?

Vaitheeshvaran Selvarasu @Vaitheeshvaran_Selvarasu

06 June 2018 0 2K Report

Actually How much abs it (DPPH) will give? and How can I check my abs value is correct ?

Either i should increase my concentration of DPPH from 0.1mM to 0.5 or 1 mM or Increase the Volume of Control (DPPH).

Badges
Science topic

Similar topics
Correction

More Vaitheeshvaran Selvarasu's questions See All

Can anyone suggest online site to do karyotyping, especially for beginners ?

I want to do Karyotyping in online. Is there any free websites available to do karyotyping for free...

06 July 2019 9,821 1 View

How to get the Chemical compound Pharmological Properties via any website or software? If any specific method available to retrieve information ?

Particular website or software to get the full available information of chemical compound, especially the biological role of a specific chemical compound.

04 May 2018 9,585 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View