Level 1 pre-post multilevel regression: Panel data or ANOVA approach?

Dear colleagues, I am currently teaching myself in multilevel analysis using educational data. I found few to zero literature on basic analysis methods. In my context we frequently use level-1...

17 February 2021 9,378 5 View

Reliable and Valid Instrument for Causes of Medical Errors?

Is there any questionnaire/survey that measures the causes of medical errors? Example: physician negligence vs. systemic issues. Looking for a reliable and validated instrument. Thank you!

15 February 2021 2,874 4 View

Should the AUC in a concentration-time graph of a subcutaneous implant be roughly the same for poeple?

I have 2 concentration time curves of a subcut drug implant. the first group has a peak around the 50 day mark where as the second group does not. Both groups received the same implant by the same...

10 February 2021 2,305 3 View

Software for flow cytometry-like gating of data sets?

I am currently trying to do image based cytometry from fluorescence microscopy images. From the images I extract data such as cell size and a number of fluorescence intensities. Is there any...

09 February 2021 6,278 1 View

Can A. thaliana splice algae genes?

24 January 2021 329 2 View

Does long term preservation (10years) of Collembola in 99% Ethanol affect recovery rate of extraction by flotation?

Hello! I am currently developing an automated counting approach using Fiji to count Collembola from pitfall trapped samples that have been stored in Ethanol (99%) since 2010. I use flotation (tap...

13 January 2021 659 2 View

Co-stain Lectin PNA FITC conjugate with an uncojugated primary antibody?

Hello, I am planning to stain retinal tissue sections for IHC and want to co-stain cones and rods. For this we plan on using a Lectin PNA From Arachis hypogaea (peanut), FITC Conjugate for cones...

12 January 2021 583 1 View

How to use Abaqus USDFLD subroutine to vary stiffness?

Hi I have a problem where I am trying to vary the stiffness spatially across a structured interface. The whole idea is to vary the stiffness vertically, with a bulk stiffness of 8GPa decreasing...

06 January 2021 262 3 View

I really need help with cov-2 pseudotyped lentivirus production. Support?

Hi, i'm desesperate. i'm trying to produce lentivirus usinf BEI resources kit NR-52948. 24 hours after transfection i detect a massive GFP expression in my 293T cells. After 72 hours i filtered...

30 December 2020 9,889 6 View

How can i estimate the total phenolic content from a plant extract?

Suggestions and recommendations are welcome. A protocol used and experience would also be helpful.

25 December 2020 9,807 4 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

VIF very high, but correlation is low and coefficient is significant. Which one whould I choose?

Hello. I have a question whether if my coefficients (statistically significant) would be valid when VIFs are really high. In my model, there are independent variables(IV), moderating variables...

26 February 2021 956 13 View

What are the application of Fixed points thoery in Chemistry.?

It is said that fixed point theory has lot of applications not in the field of mathematics only but also in various areas. So I am looking for applications in Chemistry only..

26 February 2021 3,533 1 View