Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Could you please recommend some good journal that accept very long revie papers (approximately 6000+ words) in neurosurgery, cancer biology ?

Could you please recommend some good journal that accept very long revie papers (approximately 6000+ words) in neurosurgery, cancer biology ?

01 March 2021 8,087 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Errors in DNA sequences?

I am trying to better understand the scope of DNA replication and sequencing errors, e.g. 1. I have seen similar error rates of 10e4 to 10e5 for cell & instrumental DNA replication,...

24 February 2021 4,397 3 View

Does PHA-P stimulate the proliferation of lymphocytes from mice?

Hello, I will start performing MLR using lymphocytes from mice's spleen and I would like to know the better way for the stimulation. If is using PHA-P or CD3/CD28? I would like to know as well if...

23 February 2021 5,476 4 View

Could not amplify CD28 and CD3z ectodomain from cDNA of Jurkat Cells ?

For my experiments, I have to express ectodomains of human CD28 and CD3z. As a source, I extracted RNA from Jurkat cells and verified the quality of RNA on the gel. I, then, prepared cDNA using...

23 February 2021 7,051 4 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

Can bacterial suspension be pipetted directly onto petri dish and agar poured onto it?

Hi, recently I encountered a protocol for plating which was not the usual method I have been practicing (pour LB agar onto plate, allow it to solidify, pipette bacterial suspension onto plate,...

28 February 2021 7,292 3 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

Difficulty in cloning of 1kb gene into vector?

I am facing difficulties in cloning a 1kb gene into a vector (pJIT163). I have my gene on interest (GOI) in pUC57 and want to clone in pJIT163 using SalI and BamHI restriction sites. I am getting...

25 February 2021 3,221 7 View

Can cells be reused after using WST 8/ CCK 8 from Sigma Aldrich?

Hi all, Can cells be reused after I have seed them onto 96 well plates and test them with cell counting kit at OD450 (CCK8) at 12 hours, wash them with PBS x3 and add new media and let them...

24 February 2021 5,072 1 View

Standard curve shifting over time. How do I stabilise the ELISA?

24 February 2021 1,365 3 View

Is it harmful to breed for Cre Homozygosity initially?

Hello, I am currently using a Cas9 knock in system that will be expressed in the liver. To do so STOP codon fl/fl Cas9 KI mice were bred with Albumin-Cre mice to generate heterozgous pups, that...

24 February 2021 5,759 3 View