For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Which is the best kit to detect urea level in primary hepatocytes culture? Any published references?

I need to measure the urea level in the cell culture system as well as culture media? Any recommendations?

02 November 2020 1,493 1 View

How to calculate various constants used in the Herschel Bulky model from exp data (shear stress vs shear rate) to elaborate flow type of fluids ?

How to calculate various constants like consistency index and flow behavior index, used in the Herschel Bulky model from exp data (shear stress vs shear rate) in Origin or excel? If I need to...

22 August 2020 8,904 7 View

Kindly suggest me book, video lectures for analysis partial differential equations and ordinary differential equations in MATLAB?

Detailed analysis for all these in MATLAB

19 May 2020 4,214 3 View

What is the type of magnetism in the curve?

I am attaching M-H curve. If any more information is needed, I shall do the needful.

15 April 2020 8,791 12 View

Please suggest for the critical parameters that are to be evaluated during simulation of a solar cell in COMSOL multiphysics tool?

Presently I am implementing solar cell in COMSOL multiphysics 3D time-varying structure. Kindly suggest me for the basic parameters that can be evaluated from a simulation model for concluding the...

10 March 2020 830 4 View

Need a brief idea about efficiency increasing in solar cell with geometric parameters?

I need to know about what parameters can be taken for efficiency calculation in the solar cell by COMSOL simulation

05 March 2020 1,330 7 View

Can Gallium doped with Graphene? if yes than what is its effect in Band Gap, electronic property and various other properties of graphene?

How Gallium affect the properties of graphene and can i treat Ga dopoed graphene as semiconductor?

29 May 2019 2,111 3 View

No title

please let me know about the journal

10 October 2018 4,004 3 View

How to know whether dopant ions are occupying interstitial sites in the lattice OR, replacing the host cations from their lattice positions?

I have prepared Y2O3 nanoparticles doped with 3% Ag & 3% Tb (at. wt. %). Now, how can I know the locations of Ag+ & Y3+ ions in the doped Y2O3 crystal? Also how we can keep the charge balance in...

15 September 2018 5,875 7 View

Energy minimization in LAMMPS using NVT ?

How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...

01 March 2021 2,294 3 View

How can I edit suggested publications?

Hi there! I regularly receive suggestion about papers and authors that are totally out of my area. Does anybody know how I can fix this? Thank you!

01 March 2021 9,574 4 View

Can you perform the Murexide test on samples fixed in Formalin?

I have a fixed sample and would like to use the murexide reaction to test for uric acid composition. I no longer have fresh samples

22 February 2021 1,328 1 View

Monte Carlo simulation?

Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...

22 February 2021 3,680 4 View

How would I use a glycerol fixation to fix whole brain Drosophila tissue?

I need to take IF images with DAPI on a confocal but I need to use a glycerol fixation. Has anyone done this method before, if so how was it done? Thank you.

21 February 2021 3,081 3 View

Is there any general protocol for immunohistology staining?

I have some fixed slides of tissue and need to do some staining, but I am not sure where to start. There are many protocols online. Any suggestions?

17 February 2021 3,062 4 View

Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View

How can a reference point be fixed to an attachment point in Abaqus?

I am currently trying to copy an assembly feature, that is present in an old version of the model I am using, onto a new model. The feature is a reference point that is fixed to an attachment...

16 February 2021 8,872 2 View

What test should I use?

15 February 2021 911 5 View

What kind of tape can be used to fix the samples on an XRD machine?

I have a very thin sample, the thickness is around 1 mm. I want to do X-ray diffraction measurement on the thin side of the sample. What kind of tape can I use to fix the sample, and will not...

13 February 2021 4,153 3 View