I want to laminate 8 LTCC 5 mil tapes using uniaxial method. What force I will provide on tape. Please justify?

03 June 2022 0 8K Report

What is the process for uniaxial lamination for LTCC. What force I will provide on 3 x 3 inch, 8 tapes?

Badges
Science topic

More Lokesh Kulhari's questions See All

Treatment protocol for SRSE - what works best?

As we know the devastating outcome in Children with SRSE looking for further insights from researchers across the world as what they are trying to get better outcomes for these Children Is Early...

11 May 2024 4,713 0 View

Yeast Cell Glucose Uptake Assay ? Can yeast release more glucose into the reaction, when treated with test compound ?

Hi all, We performed Yeast-Cell-Glucose-Uptake assay to estimate the antidiabetic potential of the test compound. The Metformin treated yeast cells, resulted in taking up more glucse than normal...

02 April 2024 7,657 2 View

Ethical Clearance for Zebrafish in India ?

Do we need a Ethical Approval / Clearance, for working with Zebrafish in India ? There is argument, as in, it is not required and required in some country. What is the requirement in India ? So...

07 October 2023 5,997 1 View

What is the work function (in eV) for a silver nanowires?

The work function of bulk silver is cited as 4.6eV. Will there be any change in the work function of the metal when the dimension is reduced to nanometer? In this case a nanowire whose diameter is...

21 September 2023 7,529 3 View

Can anyone provide Ammonia Stripping Technology for Landfill Leachate Treatment?

There is a requirement for Landfill Leachate Treatment for ammonia and other pollutants removal. Can anyone help me by providing a project of Ammonia Stripping or similar technology for Landfill...

15 July 2023 1,312 3 View

How Stainless Steel/ copper sheet bond with PET/ Polyester to make etch heater?

I want to develop etch heater on PET/ Polyester sheet. So how I can bond Stainless Steel/ copper sheet so that I can make etching on it. As we are doing on silicon rubber.

14 March 2023 2,583 0 View

At what step do we finalize our research topic as a phd research scholar?

Arrange these in a sequential order, what comes first 1. Finalize a topic 2. Literature Review 3. Research 4. Research Methodology 5. Synopsis

12 March 2023 2,006 7 View

What is the best suited method to evenly distribute rGO on a glass subtrate?

The substrate used is a microscopic glass slide. rGO is dispersed in NMP (N-Methyl-2-pyrrolidone) to form a dispersed solution. What is the best suited deposition technique to obtain an even...

05 March 2023 5,599 2 View

Is it possible to produce thin flakes of rGO?

rGO was obtained by reducing GO that was synthesized by modified hummers method. If it is possible to produce thin flakes of rGO from a bult rGO, how could we characterize so that I can prove the...

28 February 2023 5,609 4 View

What is the order of Critical current density of Rare Earth composite in Bulk YBCO superconductor?

I currently work on YBCO superconductor and wants to dope a Rare Earth element in YBCO so I want the order of critical current density in YBCO for best results. Thankyou

08 February 2023 1,885 0 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

What causes bandgaps in periodic elastic laminates?

I've been trying to find an explanation for why bandgaps can form in periodic elastic laminates but so far I haven't found a good explanation. Can anyone point me to any resources which might...

01 May 2024 2,241 1 View

What are the testing methods to verify Electrical conductivity in Carbon Fiber Reinforced Plastics?

Testing methods to determine how well electrical current can pass through the manufactured CFRP composite laminates

23 March 2024 8,846 3 View

What method to use for uncertainty quantification using Python in Abaqus?

I need to perform uncertainty quantification by Monte Carlo Method, using Python in Abaqus, of the laminate grades (ply angle) and variation of the amount of fiber and resin. What recommendation...

03 March 2024 1,985 2 View

What may be the reason(s) for lamination in cold isostatically pressed carbon(graphite) containing refractory products?

#CIP #cold isostatically pressed #carbon refractory #lamination

04 December 2023 8,850 3 View

What kind of that i select metal and fibers/ epoxy is more prominent for fiber metal laminate using nanoclay research?

Recently i have been studied various kinds of paper on the besis of FMLs on Epoxy/fibers , there various kinds of metal and epoxy or fibers are used...so i am now quite confused that what kind of...

09 September 2023 7,654 0 View

How to reduce compressive stiffness when performing low velocity impact (LVI) and compression after impact (CAI) simulation in ABAQUS ?

I was trying to create a FEM model of an LVI and CAI experiment. For the CAI simulation, the load displacement curve I obtained is way too stiff compared to the experimental result. The maximum...

06 July 2023 1,742 6 View

In the torsional stiffness (GJ) and bending stiffness(EI), is the G and E membrane stiffness or bending stiffness??

Are the G in the torsional stiffness (GJ) and the E in the bending stiffness (EI), the membrane stiffness or bending stiffness? I think torsion and bending are the out-plane stress. So in this...

06 May 2023 3,952 0 View

How dry sodium silicate solution fast without heating?

Hello hi I would like to know, how the sodium silicate solution (55% solid) dried faster without heating in the lamination of aluminum and cloth.

04 May 2023 2,770 0 View

Does the lower temperature and lower humidity effects the curing time of 2component solvent free adhesive for lamination. If yes then how to resolve?

To overcome this problem Polyether, polyester based, or some other technology will have great result in curing properties. Please help me in detail.

19 April 2023 2,721 0 View