I need urgent help in simulation of indirect field control (IFOC) of DFIM/DFIG in matlab/simulink

More Oussama Brahmi's questions See All

Looking for help on sem image analysis?

Hello I am conducting a microstructural analysis of a soil treated with lime. The following sem images are of the untreated s1 and treated soil s3. The untreated soil contains quartz calcite...

01 August 2024 572 0 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

How to Trace velocity plot u(t) using comsol?

Hello How can I get the velocity plot u(t) of a rising bubble using COMSOL like in this tutorial...

24 June 2024 9,441 6 View

How can we select the best energy storage system for our Microdrid, and what are the best energy storage devices to be included?

There exist a wide range of technologies used for energy storage such as electrochemical (batteries), electrical (supercapacitors), mechanical,...etc. What are the best and the most efficient...

17 May 2024 3,412 1 View

Specific capacitance values?

Why specific capacitance calculated from cyclic voltammetery is different from the one calculated from charge-discharge? Ps1: I used the same potential window. Ps2: the charge-discharge curve is...

18 April 2024 9,691 1 View

The amount of water needed during the impregnation?

How much water is typically used during the impregnation step? is there any relationship between the weight of carbon and the amount of water?

12 April 2024 2,952 0 View

I need help designing an H Infinity controller to control a wind energy conversion system ?

What is the best approach to design an H infinity controller for a linear model of a wind energy conversion system, with the goal of simulating it in Simulink? Any specific methods or tools...

26 March 2024 4,008 1 View

Time of N2 injection during chemical activation?

Dear researchers, during chemical activation, when should i start injecting N2 to the precursor? is it at the same time when start heating or until reaching the desired temperature ? thanks in...

23 February 2024 1,307 9 View

How to repair a furnce alumina tube?

the furnace i am using for activation has been damaged, the alumina tube broke , i need a good glue to fix it!

12 November 2023 5,248 1 View

Why i am getting no dischage even after long time?

during GCD, i am seeing no discharge after long time of charging?

12 November 2023 7,295 12 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Dear Professor/Researcher, I want to use LoRa to send a signal with a frequency of 10 kHz. Is this feasible or not?

I use LoRa with Matlab/Simulink

23 June 2024 3,847 3 View

Aspen Adsorption linking to MATLab ??

Hi, I am looking to link MATLAB to Aspen Adsorption. I know that for Aspen Plus, it is possible to use actxserver(). Does anyone know if the same method can be used for Aspen Adsorption as well?...

20 June 2024 8,338 2 View

Does anyone know where this module is in Simulink?

I try to build a three-phase wireless power transmission model and saw this module in an article.

27 May 2024 3,471 2 View

Can you help me for do this matlab simulink project?

I'm new. I know just little use of matlab. Help me for do this matlab simulink project.

25 May 2024 4,247 1 View

Simulink model for ANC earmuffs?

Adaptive Filters are core of the ANC system. They continuously adjusts its filter coefficients to minimize the error signal, effectively generating the anti-noise signal. Common choices include...

21 April 2024 4,468 1 View

I need help designing an H Infinity controller to control a wind energy conversion system ?

What is the best approach to design an H infinity controller for a linear model of a wind energy conversion system, with the goal of simulating it in Simulink? Any specific methods or tools...

26 March 2024 4,008 1 View

Any suggestions to implement TECS on MatLab/Simulink?

Hi, I am trying to implement the TECS core algorithm to my closed-loop 3DoF model of the aircraft in MatLab/Simulink. The tuning of the innermost loops was accomplished succesfully, but now I am...

17 March 2024 8,446 1 View

Who has work on droop control for grid forming ??

could we make grid forming as stand alone inverter and control it by add active power ref and frequancy and voltage for rl load ? who has work on it in matlab simulink ? for me i did it for rl...

11 March 2024 6,303 0 View

Find a controller for a feedback-loop?

My team and I are working on an automation project to stabilize the altitude of an airplane. However, we've encountered an issue that seems unsolvable for us, at least for the moment, in the final...

03 March 2024 7,659 0 View

Ravi Verma

Can you provide some information here?

Muhammad Ali

Please, first follow https://www.youtube.com/watch?v=ddHO1D6_FAw

https://www.mathworks.com/videos/what-is-field-oriented-control-1538568554720.html

https://au.mathworks.com/help/physmod/sps/powersys/ref/fieldorientedcontroller.html

http://download.garuda.ristekdikti.go.id/article.php?article=1305473&val=146&title=DIRECT%20AND%20INDIRECT%20VECTOR%20CONTROL%20OF%20A%20DOUBLY%20FED%20INDUCTION%20GENERATOR%20BASED%20IN%20A%20WIND%20ENERGY%20CONVERSION%20SYSTEM

Good luck

Bashar Salih

I hope the following article will help you

Article Direct and indirect vector control of a doubly fed induction...

With my regards