I need to coat platinum over carbon electrodes 1x3cm size. Can anyone give me the protocol for it?

More Bhim Thapa's questions See All

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Can anyone give me the name of Universities which accept PHD after undergraduate degree ?

Any Universities which accept students to PHD program after a undergraduate degree.

06 July 2024 3,903 2 View

How can we do power system state estimation using ML?

I am trying to do a matlab project on power system state estimation. I am doing using WLS,EKF and particle filter method and then comparing these all. To minimize the error can we use Machine...

04 July 2024 6,845 0 View

What are possible sample selection biases in Logit model estimation?

I randomly interviewed 250 poor people and 250 non-poor people. Considering 1 for poor and 0 otherwise, does estimating a logit model aiming to capture the probability of becoming poor make sense?...

02 June 2024 2,326 2 View

Why are all the R2 values so low in stress vs Shear rate plot? And why can’t the Cassini model be selected in stress vs shear rate analysis?

I would be grateful if anyone could provide the answer to these question. I am using discovery hybrid rheometer HR-3. Thanks a lot

31 January 2024 4,402 0 View

Do anyone have any idea why the R2 values so low in all the rheological models in shear stress vs shear rate ?

I was hoping to find yield stress value using Carson or Herschel bulk key model.. I tried to fit viscosity vs shear rate plots to these models. Howeve, I can’t select these two model in our...

31 January 2024 6,318 0 View

How to calculate polymorphic information content (PIC) value for SCoT marker data? Which software helps to calculate it?

I am trying to evaluate the genetic homogeneity of wild grown mother plant and tissue culture raised plants of Piper sp. using SCoT and other dominant markers.

06 December 2023 1,837 0 View

How can I fit my data into rheological models and calculate the rheological parameters from the model?

I have plots of shear stress vs shear rate and viscosity vs shear rate. I want to check which rheological model do my systems (hydrogels) follow and calculate the parameters form the best fitting...

14 November 2023 6,377 7 View

What is the best treatment of hilar cholangiocarcinoma at india?

67/M smoker with recent itching and jaundice of 10 day

25 September 2023 6,351 1 View

What are the current approaches used to correct atmospheric delays in interferograms generated from Sentinel-1?

Greetings, fellow inSAR enthusiasts! I would appreciate your insights regarding the prevailing techniques employed to rectify atmospheric artifacts in SAR interferometry. Could you kindly provide...

11 July 2023 7,379 0 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Why activated CAR-Jurkat cell could not kill targets?

Previously when I co-coluture anti-CD19(FMC63) CAR-Jurkat with Raji with E:T=5:1, Jurkat can eliminate Raji in 24h. However, when I test another CAR construct, although I can dectect totally CD69...

06 August 2024 641 2 View

How much total RNA concentration to be extracted from sorted plasma cells from bone marrow of C57BL/6 mice for RT-PCR ?

i have sorted anti-NP specific plasma cells from bone marrow of C57BL/6 mice at certain times after immunization with variable counts and isolated total RNA using TRIZOL method for RT-PCR using...

05 August 2024 8,835 1 View

How to use Density Functional Theory to calculate carrier mobilities of solid system?

Hello, everyone. I have tried to determine carrier motilities of some materials, by Density Functional Theory, using Quantum ESPRESSO. There are a few methods to do it, like a package called...

04 August 2024 8,894 1 View

Does long-term culture of murine Monocytes result in macrophage differentiation?

Hi, I am isolating monocytes from the bone marrow using the Mouse Monocyte EasySep kit. I want to treat these cells and monitor expression of specific markers over the course of 10 days. I will...

04 August 2024 7,282 2 View

How can I get my Granzyme B flow cytometry stain to be consistent?

I have used PE and PE-Dazzle 594 fluorochromes and have managed to get NK cells to properly show GranzymeB expression after 4 hr PMA/ionomycin stimulaton, but for some reason my CD8 cells in the...

01 August 2024 7,677 2 View

Guillaume Rosaz

Any PVD methode (i.e. e-beam evap or sputtering) may be the most suitable to get a pure material. They are also very easy to set up.

Alain Celzard

Partha Sarathy

Platinum in powder form ? - spray coat - mix it with suitable solvent get an air gun/air brush and spray it over the carbon electrode.

Even can try screen printing