I need to built pvdf and some pvdf doped polymers in material studio. can anyone suggest me how to do ?

22 April 2017 1 4K Report

i need to construct pvdf and some polymers doped in pvdf using material studio software.

I use ChemSketch to build my molecules. It's pretty straightforward and free. You can then transfer the molecule to your MD software of interest.

Badges
Science topic

More Soma Sekhar's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

How to explain the different interaction between soluble and insoluble polymer in water?

Hello everyone, I am try to understand the differences interaction between insoluble and soluble polymers in water with metal ions and how theit charge density (of metal ions) affect the interaction.

29 July 2024 6,350 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please introduce me the latest published articles on the structure and properties of metal nanocomposites?

26 July 2024 2,200 3 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

Best method for extracting RNA from morulae?

Best method and number of embryos for extracting RNA from pig morulae?

21 July 2024 4,398 1 View

What is the difference between coordination polymer, MOFs, MCOFs?

Wherever I have referred, it puts me in a dilemma about the exact differences between these. It would be really helpful if someone can put me out of this trouble.

21 July 2024 3,045 3 View