I Need suggestions for open source softwares for slope stability analysis for landslide studies?

More Ramesh Veerappan's questions See All

How to find peak period and significant wave height for a particular location in ocean?

I want to develop the figure like attached figure. How can I get, peak period and significant wave height at any given location.

13 July 2024 886 2 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Dear All, I have to plot a wave data similar to the attached figure in matlab. Anyone please help me in this?

How to plot like attached figure in matlab?..

25 June 2024 7,220 4 View

How to calculate drug loading and Encapsulation efficiency ?

Even after using the formula i am not getting the answer can anyone help me with one example .

28 May 2024 4,503 1 View

Black dots in cell culture ?

We have been getting this black dots in our cell culture. But it is not affecting pH of media (no color change observed) until 4 or 5 days. Cells are attaining morphology within 24hrs but once the...

12 May 2024 9,284 4 View

Increasing nozzles height of drone spryaing system increases droplet size. What could be the reason behind it? ?

03 March 2024 4,127 0 View

Which is the more accurate method to calculate LUMO value for a D-A system?

Which is the more accurate method to calculate LUMO value for a D-A system? Either it from absorption edge or from CV measurement on reduction side?

15 February 2024 5,635 1 View

How do I overcome or eliminate this noise problem during patch clamp recordings?

Hello everyone, I recently encountered a noise problem in my patch clamp experiments. I happened to observe a small current and a noise when the electrode holder was in the open circuit. The...

28 January 2024 927 3 View

How long does it take to culture single colonies from single suspension cell in a 96-well plate?

Hello! I have been culturing GM11994- B lymphocyte cells from Coriell Institute. They are suspension cells and like to grow in colonies. However, after genetic modifications, I sorted single cells...

09 January 2024 7,779 0 View

How to calculate composite cylinders vibrations?

Papers that compute natural frequencies of cylinders made of composite materials.

29 October 2023 6,669 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

What precautions should be taken while handling S. aureus enterotoxin Type B in the lab?

I would like to understand potential safety concerns while handling SEB in the lab. Especially while working in animal house facility. Would like to know precautions for handling. Sigma MSDS...

07 August 2024 6,034 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Ramli Nazir

There are no specific suggestion for that. Every software developer will say that their software is the best. Infact for slope problem it is an indeterminate solution. Thus you have to find the best to suit with your slope problem. Try any available software and back analyse to see the reliability of your answer.

Atiku Sadiq

https://www.researchgate.net/go.Deref.html?url=http%3A%2F%2Fwww.geo.ncu.edu.tw%2Fseminar%2F9902%2F33_rep.ppsx

Wissem Gallala

http://landslides.usgs.gov/research/software.php