Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

What is the difference between PBE and PBEsol functional?

Hello, I am a 3rd year chemistry student and I'm writing my project report on computational chemistry. does anyone know how PBEsol improves upon the PBE functional? Thanks in advance

19 February 2021 7,068 4 View

Can someone help me with this error that I am getting while estimating a VAR model in R?

I am using annual time series data to estimate a VAR model in R. However, when I run the command to find the optimal lag length, I get the following error: Fehler in VARselect(data, lag.max = 10,...

18 February 2021 9,647 3 View

In your experience what is the difference between G.652D and G.655D optical fiber. In field and in lab?

In our current era there is a big confusion about the usage of G.652 and G.655 optical fiber cable. Theoretically G.655 is much better than G.652 but the operator feel that G.652 is giving almost...

11 February 2021 4,006 8 View

How many dilutions are good enough for TCOD50 of SARS-CoV-2?

I started with 10e-1 till 10e-10. But when I searched for online calculator they mostly consider 5 dilutions. Is there a reason behind it or I should make less dilutions?

11 February 2021 5,839 3 View

Protocol for bacterial samples preparation for Scanning Electron Microscopy ?

I want to prepare bacterial samples to observe the bacterial cell lysis by bacteriophage protein (endolysin) through scanning electron microscopy. Please, anyone can share the protocol of...

01 February 2021 1,173 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

How to find natural frequency of a bridge from vehicle induced vibrations?

i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...

22 February 2021 10,004 3 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

How can I get "Matlab/Simulink model for Droop/Reverse Droop controllers"?

Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...

22 February 2021 8,647 2 View

The Role of Town Planners in CAV Use?

Colleagues and I are about to begin a project investigating the role of town planners and local authorities in establishing the introduction of connected and autonomous vehicles (CAVs). What...

21 February 2021 2,247 3 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

How to Measure Consumer Willingness To Change from petroleum-fueled vehicle to electric vehicle?

I wanted to calculate the probability of one consumer shifting from using a petroleum-fueled vehicle to an electric vehicle. Since my background is in engineering I do not know much about how to...

15 February 2021 9,190 5 View

How to get actual or true SoC while predicting SoC for Batteries using Data Driven Approaches?

I have seen it in multiple research articles that authors use certain approaches to predict electric vehicle battery's state of charge(SoC) and then they compare it with battery's true SoC. So I...

11 February 2021 9,070 3 View

What's support me on Simulink Matlab Model of Regenerative Braking in DC Traction ?

I have a thesis on Utilize the electrical power from Regenerative Braking in 750 Vdc Traction by simulation in the Program MATLAB Simulink. I made the Power Load flow from 24kV to Traction...

08 February 2021 2,532 1 View