I had a table of aerofoil creation key points i.e x-y points, when I I'm developing the aerofoil in SOLIDWORKS,it show error curve intersecting??

08 October 2021 1 9K Report

If anyone worked on this aerofoil please let me and give the reason of error and suggest solution. I have attached the picture of the point.

Mohammad Taheripur

I think you can solve the problem by adding a third column of Z points that all of them should be one coordinate like "0.0". SolidWorks expects three columns for the import data, without it, you might be getting an error.

Badges
Science topic

More Anwar UL Haq's questions See All

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

What is the difference between AC conductivity and DC conductivity? Is AC conductivity = ionic and DC conductivity = electronic?

I am reading papers on batteries and although mostly people have reported ionic conductivity in Scm-1 but some have reported DC conductivity as well I and am confused as to what that is. Any help...

21 February 2021 9,207 6 View

What influences inter-day reproducibility in UPLC-MS/MS analysis?

I was analyzing some metabolites in human plasma. While the intraday precision of these metabolites was acceptable ( less than 20%), the interday precision was quite large. So what influences...

13 February 2021 9,183 9 View

Where can I find FDI data by sector/industry for Asian countries like India and China for the last 30 years?

Common databanks like UNCTAD, OECD, WorldBank and ASEAN Website did not have the data for the last 30 years.

09 February 2021 4,701 4 View

What is impact of sampling frequency on deep learning?

Greetings, everyone. I am a bit curious to know how the sampling frequency of the device that captures the physiological signals impact the deep learning process. For example, if a device abc...

03 February 2021 379 4 View

Why sometimes current- voltage plot in chemiresistors/ FET does not pass through the origin?

I am trying to measure resistance from I-V curve from a chemiresistor/ FET sensor with a keithly sourcemeter. The substrate is soaked/ wet with protein and phosphate buffer only. But the I-V line...

24 January 2021 8,009 3 View

How to solve AMPS 1D simulation error?

I am trying to model a photovoltaic device using AMPS-1D software. But once I am submitting it to the queue, it remains there for an infinite amount of time without giving the result. I couldn't...

11 January 2021 9,801 2 View

How to interact with internal memory of FPGA and connect it a signal or array inside a module?

I am trying to implement a processor tile on FPGA using vivado but it is taking too long to synthesize design due to large amount of Instruction and Data Memory. Currently, I have put complete...

05 January 2021 8,349 1 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Is stone a sustainable material? Is it a sustainable approach to use natural stone waste in architecture?

I'm designing a zero-waste restaurant and considering using marble waste to make some tables and a bar countertop. My clients think it's not "sustainable enough" and I would like to have more...

01 March 2021 4,326 7 View

Does any one can help me choose a reasonable basis set for intermediate metal ions interactions with guanine (i.e Fe2+, Mn2+, Cu2+ and exc.)?

Hello every body Does any one has any idea to help me choose a reasonable basis set for intermediate metal ions (i.e Fe2+, Mn2+, Cu2+ and exc.) interactions with guanine or other DNA organic...

01 March 2021 6,187 2 View

What could be some reasons why unstimulated monocytes are getting activated?

Im doing PBMC isolation -> CD14+ enrichment using magnetic beads -> stimulation setup. My negative control is just cells in cRPMI but they seem to get activated over and over again.

28 February 2021 7,883 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

How the values of errors can be calculated for thermodynamic data?

I have calculated thermodynamic parameters for surfactant solutions in aqueous and mixed alcoholic solvents. I want to calculate the value of errors in the data and represent it in the table along...

22 February 2021 239 2 View

What might be the reason for obtaining two bands in plant genomic DNA extraction?

I got a thin band and a thick band i guess it would be the genomic DNA and the 260/280 ratio is 3.

21 February 2021 6,523 6 View