How large pressure can a qartz tube sustain ?

08 September 2016 4,988 4 View

Review process of the journal of Progress in Materials Science?

According to the author guidance of Progress in Materials Science, we sent a scientific manuscript and CV of the first author about two months ago to an editor of the journal for evaluation if the...

06 July 2016 6,100 2 View

Can you give me some advice about the data fluctuation problem in the Hall resistance measurement using PPMS?

In our Hall resistance measurement using PPMS DC resistance model with four probe method, we always encounter a problem that the resistance data randomly fluctuates, so we must remeasured a same...

07 August 2014 1,473 8 View

The mobility determination when there exists anomalous hall effect?

It is well known that the mobility is always determined through standard Hall effect detection. For an ordinary Hall effect, that is easy to extract the hall coefficient. However, if the system...

07 August 2013 9,511 1 View

Why is the anomalous hall conductivity defined as -Rxy/(Rxx*Rxx+Rxy*Rxy) but not 1/(Rxy-Rxyoh)?

Where R notes resitivity, Rxyoh represents the Rxy part coming form the ordinary Hall effect.

06 July 2013 8,837 3 View

The magnitude range of the elastic scattering length and inelastic scattering length?

I hope to know in most common cituations , what range the magnitude of the elastic scattering length and inelastic scattering length is in at low temperature for a strongle correlated system as...

05 June 2013 7,371 6 View

How to treat the as received LaSrAlO4 and MgO substrates to get smooth surface with steps?

It is well known that a smooth substrate with step surface is important for growing epitaxial films. Recently, I encountered this problem on LaSrAlO4 and MgO substrates. I have tried H3PO4 etching...

02 March 2013 9,289 3 View

Could spin orbital coupling form in a perfect crystal without inversion symmetry structure?

In my knowledge, near all of the publications say the spin obtial coupling originates from the moving of a spin electron relative to a atom, and there are two mechanisms to induce SOC, i.e. the...

31 December 2012 8,619 2 View

Does anyone have the crystal structure data (CIF or other format) of SrRuO3 with group Pnma?

-

09 October 2012 989 0 View

Strange result of a negative film temperature enhancement in 3 omega method measurement

We recently used the 3 omega method to detect the thermal conductivity of a film with about 100nm thickness on a STO substrate with thickness about 500um. In the detection, we strangely found the...

08 September 2012 9,006 6 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View