I added mistakely the oil to the oil mist filter opening of the dry vacuum pump, what will happen and how I can fix this problem?

07 September 2023 1 8K Report

Jack Silver

The excess oil will spray out of the top. Remove the mist filter and drain as much oil as possible. You'll have oil coming out of the top until most of it has been blown away.

Badges
Science topic

More Rana Hakimi's questions See All

How to do pca analysis of c-alpha atom of the protein?

i m interested in pca analysis of c-alpha atoms in gromacs for that i used the following gmx_mpi covar -s mdca.tpr -f mdca.xtc -o eigenvalca.xvg -v eigenvecca.trr -av average.pdb -n index.ndx but...

30 July 2024 1,607 1 View

Getting this error : gmx_mpi': corrupted size vs. prev_size: 0x0000000001d1b320 ***?

i am using the trjconv command in gromacs gmx_mpi -debug trjconv -s md.gro -f md.xtc -o utr.xtc -fit rot+trans and after few steps i got the error gmx_mpi': corrupted size vs. prev_size:...

17 July 2024 6,216 1 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Any suggestions to enhance the wettability and adhesion of fluorosilanes?

I am facing a difficulty to prepare the thin film which contains fluorine contained silica monomer, as we know F is highly reactive with low surface energy and it could be the reason of low...

09 July 2024 6,017 3 View

Why is the mouse intestinal organoid not forming ?

I am isolating the crypt from mouse small intestine the following several modification of EDTA concentration, 3mM (30 min), 5mM (30 min), 20mM (25 min) at 4 degree. For all the EDTA...

09 May 2024 9,005 2 View

What correction is used when 95%aCI is overlap ?

How we make 95% CI (lower and upper) far, when overlap in analysis, whether we can use effect size to make difference in lower and upper interval

03 May 2024 1,846 2 View

Is Pluriselect a good company to buy kits for cell separation?

I am recently buying kits from Pluriselect to take out (deplete) NK cells and CD4 cells from blood. The main reason me using this is cheap and do not require accessory equipment. But in Pubmed...

02 May 2024 5,861 1 View

WARNING: FENE bond too long: 1 7 8 32968539.141547877 (src/MOLECULE/bond_fene.cpp:83) ERROR on proc 0: Bad FENE bond (src/MOLECULE/bond_fene.cpp:85)?

# Polymer chain simulation with FENE and LJ potential in NVT ensemble # Initialization units lj # Use LJ units atom_style bond # Atoms and bonds boundary p p...

16 April 2024 5,828 0 View

Bond broken in fene potential?

i simulating a single chain polymer with 10 particle with fene and lj but if i increase the no of particle my bonds are being broken . im using parameters as below 20 50000.0 0.1 1000.0 1.0...

15 April 2024 2,748 0 View

How to calculate the center of mass coordinate of the protein in gromacs?

i want to find center of mass coordinate of the protein,for that i using the following command gmx_mpi traj -f md_noPBC.xtc -s md.tpr -com -ox com.xvg -pbc but i m not getting satisfactory...

04 March 2024 814 4 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Do you think can be any gas and oil bearing rocks in Eastern part of Iran?

I want to know more about petroleum deposits in Iran.

02 August 2024 8,725 3 View

Does continues partial charging/discharging do any harm to the BESS performance and degradation?

For a grid connected BESS (lets say 100 MW/200 MWh system, LFP battery), if we charge the BESS in such a way that whenever we can access power from the solar that will charge the BESS. Hence it...

01 August 2024 9,903 7 View

How to Post-fix Mice pup's brains?

I need to Postfix mice brains. I slice the brains using microtome at 40 microns. These are Postnatal days 7, 11, 14, and 21. I am using half the brain for other analysis, so I need to fresh freeze...

31 July 2024 1,123 4 View

Is the black sediment consider as sand? If not, how can I filter it out?

Hi researchers! I'm working on soil texture analysis, and the end result for sand is doubtful because there is black sediment appearing after drying, as shown in the figure. Is it considered sand?...

30 July 2024 557 2 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

Heavy Crude oil PVT Data?

Hello i need heavy oil PVT data having viscoisty of 2000-3000 cP. If someone have it or research papers about it, kindly share it with me Thanks

25 July 2024 6,940 1 View

I am trying to find phonon, and when i run calculations, there is error ?

how to fix this error, from phq_readin : error # 1 DFPT with the Blochl correction is not implemented I am attaching my ph.in file.

23 July 2024 4,649 2 View

Can we isolate microplastic from sludge sample without using vacuum filter..?

isolation of microplastic from sludge sample using centrifugation ..

23 July 2024 6,418 0 View

What are the most PROBLEMS of HYBRID nanofluid in oil industry ?

explain your idea

23 July 2024 1,197 0 View