How we convert Dose-Rate <--to--> Activity Calculations (In Air), using Gamma Emitter Point Source ?

Murtadha Sh. Aswood @Murtadha_Aswood2

06 June 2017 1 380 Report

Convert the Activity to Dose Rate

Murtadha Sh. Aswood

The covert Dose rate to activity depend on the types of source and the distance

Badges
Science topic

More Murtadha Sh. Aswood's questions See All

What the good way and suitable device to measure the concentration of Radon 222 and 219?

I measured the concentration of Radon 222 and 219 in vegetable samples. I used Cr-39 to measure the concentration in that samples.

31 December 2016 3,969 6 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Experimental Design: How deal with pseudreplicates with immunological and clinical-chemical paramaeters?

Hello everybody, I am investigating the influence of a toxinon various clinical-chemical and haematological parameters in fish. I have three treatments (control, low dose, high dose) in my...

24 February 2021 1,243 1 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View

Using the Pfaffl method: Is it possible that the ratio of the calibrator does not equal 1?

Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...

19 February 2021 8,351 2 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View