How we can use dll files instead of mex files in s-functions in matlab?

More Hossein sanaee nejad's questions See All

How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software?

Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks

23 February 2021 6,518 3 View

How can I find the thermophysical properties of high temperature microencapsulated phase change materials (MPCM)?

Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...

14 February 2021 3,606 2 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

How can I find eddy size distribution in ANSYS Fluent?

Hi everyone, I'm simulating a 3D turbulent pipe flow using the SST K-W turbulence model in ANSYS Fluent. Is there any quantity among the postprocessing quantities that represent "eddy size" or...

01 February 2021 731 1 View

Is it possible to highly selective remove a fused silica template from PDMS by laser-induced backside wet etching (LIBWE) method?

Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...

22 January 2021 2,352 2 View

How to match results from based paper and Ansys Workbench in modeling piezoelectric?

Hi guys, I have modeled a laminated composite beam patched with piezoelectric layers in Ansys Workbench, but the results are far away the results reported in base paper. I have attached the...

13 January 2021 7,356 3 View

What is the gradient thermal annealing (GTA) process?

Hello to all What is the gradient thermal annealing (GTA) process?

06 January 2021 7,740 2 View

What is the difference between organic perovskite solar cell and inorganic perovskite solar cell?

Hi everyone What is the difference between organic perovskite solar cell and inorganic perovskite solar cell? Thanks

01 January 2021 4,310 6 View

How to measure both Sulfites and Sulfates Ions In water?

Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)

27 December 2020 9,350 4 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Devi Palanisamy

Refer this link

https://www.mathworks.in › ... › Calling External Functions › Call MEX File Functions

https://www.mathworks.com/matlabcentral/newsreader/view_thread/252617

Mehdi Azizi

Hi,

you can try MATLAB 6.5 to run the simulink.

Unfortunately MATLAB doesn't support .dll files in newer versions.