How to wash syringe used to inject gas sample into GC-FID?

More Tanmoy Roy Tusher's questions See All

Does "response to item ratio" has any effect on "inter-item correlation"?

Suppose a survey was conducted with a lower sample size (less than 100) for factor analysis of the items (less than 20). Now would a larger sample size increase the inter-item correlation? What...

27 December 2020 1,722 3 View

Hi all, I am facing a typical issue in co-crystals?

Although one of my drugs co-crystal is showing high melting point in comparison to others but its dissolution rate is better than the other forms... is it possible... Usually we find lower the...

21 March 2020 2,594 3 View

Is there any database that consists of detailed information about global contamination by organic pollutants?

I am searching for database, if any, which can provide me detailed information about the extent of contamination by organic pollutants (for example 1,4-dioxane) and their co-contaminants around...

14 January 2020 8,472 1 View

Is there any widely practiced research design (questionnaire/ experiment) that measures stress level during a particular task?

Generally in biomedical science, measurement of "cortisol" is used, but I am looking for some "pen & paper" procedure that strikes out blood sampling or anything like that.

09 January 2020 1,328 2 View

How to resolve "Data is missing" pop up message while defining contact interaction in Dynamic explicit Abaqus?

Using Abaqus dyn explicit to model roll forming of sheet. Rollers are rigid.

19 September 2019 3,189 2 View

I have queries about Mito tracker Green and Deepred co-cultures?

After tagging separate cell population with mitotracker Green and Deep-red, Co-culture at different time points(24hr onwards) and confluency produces same result i.e. 100% transfer/exchange of...

14 May 2019 6,567 4 View

How can I check the growth of microbial consortium that aggregates?

The microbial consortium has been enriched on mineral salt medium under aerobic conditions. I have tried by measuring OD600, dry weight concentration, and viable cell count. Since the consortium...

04 March 2019 4,153 3 View

Why havent time-evolution in CFD simulation been parallelized unlike space?

Domain decomposition in space has diverse approaches for optimal load balancing to simulate massive CFD problem in parallel. However, the time-evolution being serial seems to be a very big...

28 February 2019 6,778 6 View

How to report a series of manipulated data found in a published article to the journal editor?

Recently, I have gone through an article in a prestigious journal where most of the figures representing the main theme is manipulated. Do I need to provide any data from my side to claim the fraud?

29 October 2018 4,068 3 View

Can Co-crystallization technique be used for solubility enhancement for BCS Class II drugs?

Lot of papers on co-crystallization technique are there in literature to improve the solubility of BCS Class II drugs. can this be taken a Ph. D research project. Also request you to...

26 March 2018 3,156 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How to best wash a 96-well plate containing microplastic?

I am planning my protocol for my dissertation for an experiment quantifying bacterial (E. coli) biofilm formation on micro-plastic (5mm discs of polyethylene bags) by conducting a crystal violet...

23 February 2021 7,868 2 View

How can I improve the concentration of banana fruits extracted RNA?

Currently, I'm working with banana fruits. I've tried to do RNA extractions with different methods, and I've gotten total RNA without contamination, but I couldn't get a high concentration of...

22 February 2021 6,126 2 View

Aspen Plus Error: Unknown or undefined bead number?

Hello, in my Aspen Plus Simulation (see attachment) there are two heat exchangers. One HEX1 (oil+gas) ist fed by hot gas which ist coming out of a burner. The other HEX2 (gas+gas) shall work as a...

14 February 2021 8,096 2 View

3T3-L1 cells, is this a bacterial contamination or a cross contamination with different cell line? or something else?

Hi, I am experiencing some difficulties with 3T3-L1 cells culturing recently. I am working with 3T3-L1 cells for almost 4 years now and have seen bacterial contaminations/ unhealthy cells and...

13 February 2021 4,040 3 View

Grzegorz Boczkaj

It is true that some part can adsorb on the walls. Hamilton offer a heates block that is connected to vacuum. You can make yiur own home-made interface to a vacuum source ended with GC membrane. Connect your syringe to such an interface. Generally even fkushing wirh few volemes of inert gas should be effective.

Regards

Princewill Ikpeka

I think this might be helpful to you.

https://www.chemicalforums.com/index.php?topic=64746.0