How to use General Contact(explicit) algorithm for 2D modelling in Abaqus?

11 July 2024 1 3K Report

Hi Everyone,

I am modelling the compresion test for auxetic structure. In order to perform a realistic analysis, I need to define contact for each cell faces. However, Abaqus gives error when I try to use general contact algorithm. Do you have any suggestions or idea about this issue? Thank you very much for your help,

Regards,

Engr. Tufail

What error you are facing?

Badges
Science topic

More Yezdan Korkmaz's questions See All

Has anyone used Pierce™ Chromogenic Endotoxin Quant Kit to detect endotoxin presence on an unknown sample?

Hello everyone, I was wondering if anyone has used Pierce™ Chromogenic Endotoxin Quant Kit to detect endotoxin presence of a powder sample diluted in DMSO. Firstly, we are not sure whether our...

21 May 2022 9,742 2 View

How many ug should I choose as the protein amount when doing western blot in liver tissue?

Dear researchers, I will look at ER stress proteins from rat liver tissue by Western blot method. I found the my protein concentration to be 86.386 µg / ul. How many ug of protein should I choose...

25 January 2021 1,038 3 View

What is the importance of vermicompost application in the improvement of acid soils?

Acid soils have become increasingly big problem for agriculture and landscape areas in recent years. Adequate efficiency cannot be obtained from chemical fertilizers applied to acid soils. So it...

12 May 2020 8,362 21 View

Dear Mr Ambler. We have a problem about modelling fabric layer in ANSYS ACP. If we tell you our problem, Could you help us about it, please?

Our fabric shape is like in the attachment. The directions of this fabric are both x and y directions. In the modeling ply group of ACP we see only one fiber direction (x or y direction) , but we...

25 April 2018 5,110 3 View

Which electrolyte should I use to prevent passivization of alumium?

Hello all, I am working on electrochemical machining of aluminium alloy. But neutral electrolytes enhances the passivization. So, I am currently looking for a way to prevent passivization of...

06 April 2018 2,964 3 View

How do I read this output of lisrel?

Dear all, I am doing a moderation analysis in Lisrel and this is the output I got: Degrees of Freedom = 0 Minimum Fit Function Chi-Square = 0.0 (P = 1.00) Normal Theory Weighted Least Squares...

30 September 2017 4,145 5 View

Is this Rosa different from R. foetida or not ?

It was collected from Eastern Anatolia, Turkey

19 February 2015 8,911 15 View

Interhemispheric transfer time measurement by using ERPs

We calculate the interhemispheric transfer time by giving visual stimuli (word) and sometimes, the data appear like this in some participants in some electrodes. Does anyone know the most likely...

01 January 1970 7,949 10 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View