22 October 2021 3 9K Report

I tried to fabricate FeOOH on BiVO4/FTO through photo-assisted electrodeposition. During the electrodeposition, the layer turned to a black colour and started to fall off the FTO. What could be the reason?

More Shalini Kulandaivalu's questions See All
How to get Tafel plot from LSV graph and how to select the region to get the slope?

I'm working on water splitting. I have trouble analysing the Tafel plot. I'm not sure on choosing the right region to get the Tafel plot and slope

12 October 2022 4,897 0 View

What is the purpose of using acidic medium in the synthesis of bismuth vanadate?

In the synthesis of BiVO4, why acetic acid is normally used? what is the purpose of adding acetic acid in a solvent mixture containing acetylacetone and 2-methoxyethanol?

09 October 2021 1,763 8 View

How to determine over-potential?

In CO2 reduction or water oxidation, how to determine over-potential? Is it from LSV or CA graph?

22 September 2021 4,817 3 View

Why need to remove oxide layer of nickel foam prior to deposition?

I have performed electrochemical deposition of PEDOT/GO prepared in aq solution containing LiClO4 on nickel foam. But deposition layer does not form on the cleaned nickel foam. FYI, nickel foam...

20 November 2016 6,412 6 View

Similar questions and discussions
What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How to solve the problem of unconscious teeth grinding during sleep at night?

One of my friends, every night after falling asleep, his mouth would make a creaking sound after chewing something. This teeth grinding condition would continue until he woke up, and he didn't...

08 August 2024 1,366 5 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View

Is it fare for editors of reputed Journals to put on hold manuscripts more than six months without review updates, Are they harassing researchers?

It is being seen that Editors of some reputed Journals are putting on hold the manuscripts and not updating review states even passing more than six months from submission. Researchers are...

24 July 2024 8,596 2 View

What are the possible chelating agents to form complex with cobalt only but not nickel in the solution of nickel and cobalt sulfate?

I want to electrodeposit cobalt only leaving behind the nickel in the solution

15 July 2024 3,462 2 View

Has anyone tried freeze flow samples in -80C freezer or liquid nitrogen before processing?

Our lab has some radioactive cell samples that need to be kept frozen for at least 30 days before flow analysis. For some reason, the samples stored in liquid nitrogen did not perform as well as...

15 July 2024 9,975 1 View

I want to ask why the poly aniline film does not stick to the ITO type substrate knowing that I used the electrodeposition method?

In order to make a polyaniline film, I used the electrodeposition method and set all the conditions, but I noticed that the polymerization process is happening, but it doesn't stick to the...

09 July 2024 2,708 2 View

My Cyclic voltammetry curve doesn't show cathodic peak of Cu2+ to Cu+. how to solve this problem?

I performed CV of Cu-MOF in a buffer solution of pH 8, and we did not find any peak corresponding to Cu2+ to Cu+. What is the reason behind this? Please give your valuable suggestions.

08 July 2024 2,388 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close