How to solve "cz freeze python error in main script" Acp in Ansys probelm?

More N. C Das's questions See All

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

Can i quantify protein concentration in sds page?

I have to quantify a mixture of proteins. But I can not quantify its concentration by any protein detection methods as the values fluctuate. Can i quantify the protein concentration by sds page?

22 February 2021 215 2 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View

Can we use image data in MATLAB Neuro Fuzzy Designer ?

I have remotely sensed data (image) that I want to use in the Neuro-Fuzzy Designer apps of MATLAB. Is it possible to use an image file in the Neuro-Fuzzy Designer app or only numeric data is...

17 February 2021 1,205 5 View

Is it possible to determine % K2O of organic manures by STPB method ?

To determine % K2O of organic manures, flame photometric technique is used whereas in inrganic fertiliser for K2O determination STPB method is used. I am trying to find out any method of...

24 January 2021 4,714 3 View

How to tackle "CONSTRAINT CONTROLS" error while using tie between CFRP and frame segment in abaqus?

Hello, I had been trying to model a portal frame wrapped with CFRP in ABAQUS. To tie the CFRP laminates with frame I need to use slave/master surface interaction. But whenever I try to model the...

19 January 2021 2,906 3 View

How to remove colour from DNA pellet during DNA extraction?

I am working with Amaranth accessions which are green to red in color and contain high phenolic compounds. Using the CTAB method with the slight modification I am trying to get high-quality DNA so...

18 January 2021 3,578 1 View

Why the mixture of NaOH solution (10-12M) and Na2SIO3 solution is getting solidify after mixing?

These days I am noticing that the mixture of NaOH (NH) (10-12M) and N2SiO3 (NS) solution gets solidify after 24 hours. The ratio of mixture of NS to NH is 2. To mention, the same solutions that we...

18 January 2021 7,911 2 View

Which model is most suitable for urban simulation?

Respected sir/mam, I want to simulate the urban expansion using different time series LULC based on satellite image. please suggest me most suitable model for urban simulation. Thanks and regards.

17 January 2021 9,134 11 View

Is there any packages or code of MATLAB for solving a system of stochastic delay differential equation?

Hello, Can you help me regarding MATLAB solver for a system of stochastic delay differential equations? To be specific the system is delay differential equation where parametric stochasticity is...

15 January 2021 6,950 7 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Puneet Bawa

The location of the DLLs needs to be added to the setup.py. On Windows 10, this might be in the root of C: or installed location.

Add a variable to store that path, then make it a raw string with a leading r.

N. C Das

Sir,

Thanks for your suggestion. I also tried that. But the problem had remained the same.

The problem was related to my Windows environment. And Luckily I solved it.

Ebrahim Ahmed Ali Alkebsi