How to set Time and LUX values in AC PIR Sensor?

More Umapathi Nagappan's questions See All

How can we find that buffer solutions dielectric constant or relative permittivity?

how can we find that buffer solutions dielectric constant or relative permittivity?

09 January 2016 168 3 View

How to measure the thickness of oxide nano layer (colored) over an anodized 1mm thick Titanium piece without disturbing the structure?

Cutting and polishing disturbs the structure; bending the sheet causes stretching and subsequent fragmentation of the nano layer as observed in FE-SEM; ellipsometry is too tedious and inaccurate...

05 October 2015 2,411 18 View

I was trying to dissolve formazan crystals with acidified isopropanol and it didn't work. Is there any reason for this?

I have encapsulated my cells using chitosan at different concentrations of 1mg/ml of 0.1M acetic acid, 1mg/ml,0.1 mg/ml. I run MTT at different timepoints of Day0,Day1, Day3 and Day7. at Day 3...

28 May 2015 5,261 3 View

Does anyone know the PCR premix composition and concentration of cbbM343F and cbbM1126R?

I didn't get PCR product using general protocol.

15 March 2014 2,079 3 View

Which SAR dataset to use for generating coherency matrix and performing target decomposition (Description) ?

Working on chandrayaan-2 DFSAR data, there are three datasets available: 1) Slant range image data product: The slant range complex image file. Each pixel is represented by two 4-byte floating...

02 March 2021 8,481 3 View

How UAV or drone can be beneficial to better estimate crop yield?

As we know, crop yield estimation has been done traditionally with farmer's expert knowledge, deductive sampling in representative areas, and remote sensing with satellite imagery. Farmer's Expert...

01 March 2021 3,468 3 View

Which bacteria are suitable for quorum sensing screening?

I want to find a quorum sensing inhibitor from plant extracts. Klebsiella pneumoniae, Moraxella catarrhalis, Staphylococcus aureus, and Streptococcus pneumoniae. I looked for these strains...

01 March 2021 7,675 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

What is your preference for journals for publishing in the field of Hyperspectral Imaging or Remote sensing?

I believe that we need to share our experience in publishing in the field of Hyperspectral Imaging or remote sensing? What is the best journal that you publish with? What is the worst experience...

23 February 2021 3,411 4 View

How to use Remote sensing and GIS applications for mapping the available medicinal plants within the locality/municipality?

Hello, I'm very interested in mapping and managing the conservation of the Philippine traditional medicinal plants, in which I think is very helpful in the field of medicine for further analysis...

21 February 2021 374 5 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

How to discriminate between Sentinel-2 Level-2A Product Discriminators?

According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...

21 February 2021 5,919 9 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

Shakik Mahmud

Dear Mr. Umapathi Nagappan .

Please read this article.

Link: https://hpm.com.au/app/uploads/2018/06/hpml1167-630s01-630dm01-hpm-pir-sensors-instructions.pdf

Thank You.

Faraed Salman

At the fully anti-clockwise position, the sensor will only operate at night. You can set the sensor to operate at the desired lux level by adjusting the LUX knob. 1. When power is first switched on, the unit enters into the WARM UP period for about 30 seconds, then automatically changes into AUTO MODE.