How to prepare a perovskite solar cell sample to have a proper multi-layer cross section FESEM image?

10 October 2016 1 5K Report

I want to measure the thickness of tio2 mesoporous, perovskite and HTM layers in my perovskite solar cell samples accurately with FESEM images. but I dont know how to prepare my samples to avoid any damage in layers.

Ian J Slipper

try this link.

You might want to consider ion milling for an even better finish.

http://www.azom.com/article.aspx?ArticleID=12687

Badges
Science topic

More Ershad Parvazian's questions See All

How can I calculate the viscosity and density of perovskite solution?

I need to find out the thickness of my perovskite thinfilm via Landau-levich equation. To calculate, I need to have viscosity and density of my perovskite solution. Is there anyone to help me?

05 June 2017 3,763 0 View

Can anyone explain why these waves were formed in my perovskite layers?

I used one step spin coating deposition method with Chlorobenzene anti-solvent to fabricate MAPbI3 perovskite...However, after deposition, these waves were formed in my layers ... can anybody says...

08 September 2016 6,879 10 View

Is there any practical one-step perovskite solar cell fabrication method with high conversion efficiency?

high conversion efficiency in my idea is sth more than 14%

05 June 2016 3,818 5 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

Could it be a cell culture contamination?

Hello everyone! I observed in my culture (htert-RPE1 cells) an orange- red particle at the bottom of the dish. It is visible to the naked eye as a very very small red dot. Could it be a...

09 August 2024 2,824 3 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there any way to quantify bacterial and fungal cells in their mixed culture?

I am working in fungal fermentation of soybean meal and there is bacterial growth in them at times. I am trying to quantify fungal cell counts and bacterial cells; but I haven't been able to do at...

07 August 2024 7,535 4 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View