How to predict plasmids from plasmid spades?

18 October 2022 0 845 Report

Hi,

I am trying to find plasmids from my bacterial WGS. I want to know if for plasmid prediction I should run plasmidsSPAdes after the spades assembly pipeline or if it can be run simultaneously.

Best regards,

Badges
Science topic

Similar topics
Geoscience
Asia
India

More Ahmer Bin Hafeez's questions See All

How to solve g_mmpbsa error?

Program: g_mmpbsa, version 2024.1 Source file: extrn_apbs.cxx (line 152) Fatal error: Failed to execute command: $APBS pybYcUWA.in --output-file=pybYcUW.out

07 August 2024 6,066 0 View

Methods of teaching economics?

Answer should be based on institutional level

29 July 2024 1,506 4 View

Why binding energy is in positive number after performing mmpbsa?

I performed mmpbsa of protein-protein complex simulation on gromacs. My binding free energy is +166781. This complex is stable when experimentally produced in wet lab. In index.ndx I grouped...

19 July 2024 4,120 5 View

Claim co authorship of this article https://doi.org/10.1371/journal.pone.0301672 to add it to my account ?

28 June 2024 9,883 3 View

How to verify the correctness of an abaqus model and how to make a thermally coupled model converge to the correct values?

Hi all, I am doing a hot rolled composite simulation, but the same model, using the implicit and explicit algorithms gives the results shown below, why do the two algorithms give completely...

14 June 2024 7,737 1 View

How to find the expected Kd value of a recombinant antibody?

We produced scFv of an antibody from bacteria. Now we want to establish dissociation Kd of antibody using quantitative elisa. How can i know the expected Kd value (range in nM, or mM)?

04 June 2024 2,602 5 View

Are protein models designed computationally patentable?

If we design proteins like tetrabody or triabody with unique binding sites in silico without further wet lab validation can we patent that structure and procedure?

01 June 2024 2,493 1 View

Why Cell lines showing a high/low luminescent signal in the cAMP assay?

Hi I am Muhammad and working with an Sf9 cell line expressing neuropeptide receptors and using the cAMP-Glo™ Assay kit to measure the luminescent signal of these receptors. One of my cell lines is...

29 April 2024 8,564 0 View

How to start GROMACS simulation from a specific checkpoint?

My simulation suddenly stopped due to some reason. Now i cannot restart the simulation from previous checkpoint because it was not written properly. my _prev.cpt file is also corrupted....

18 April 2024 2,461 0 View

Why does an over-expressed enzyme protein need to be purified to show the catalytic activity?

An enzyme protein overexpressed in bacteria needs to be purified to show its activity. Why doesn't the cell lysate show activity when added to the substrate?

23 March 2024 9,450 9 View

How to confirm the site-directed mutagenesis result without performing NGS?

I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...

08 August 2024 4,645 2 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

Where should the ARS sequence be introduced on a plasmid?

Hi all, I need to introduce an ARS (autonomously replicating sequence) in my plasmid but I'm not sure which position would be the best. Does anyone have any suggestion? A picture of the plasmid...

05 August 2024 1,573 4 View

Why after performing site directed mutagenesis ,I don't see any colony after transformation?

I want to introduce a point mutation (change in one nucleotide) into my gene of interest (DNA binding domain) I have designed primers as recommended on the Data sheet of the kit : -Both primers...

05 August 2024 9,059 3 View

Why my colony PCR results of my recombinant bacterial not showing any results?

I am performing ligation of the plasmid and a target gene. The steps I have taken are: 1. Double digestion of the plasmid and target gene 2. Ligation of the plasmid with the target gene 3....

05 August 2024 2,570 3 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

How is the bacterial genome's high protein count verified as genuine despite 800+ contigs and good metrics (98.55%completeness, 0.68% contamination)?

Given that the bacterial genome has over 800 contigs, but its quality metrics are good, with a completeness of 98.55% and a contamination of 0.68% as assessed by CheckM, what specific validation...

01 August 2024 1,514 1 View

Transfection in HEK293T cells?

Dear All, I am trying to transfect a pCDNA3.1 vector containing my gene of interest. The purpose is to figure out the localization of the protein of interest. I have fused the protein with GFP on...

31 July 2024 9,892 4 View

Issues with Protein Expression in Transfected cells?

Hello I am trying to create a stable cell line in HEK293 via Lipofectamine 3000 transfection. My plasmid is a CD63-IL10-GFP construct with Puromycin resistance. I am successful with the...

30 July 2024 6,648 1 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View