How to obtain Some views in ANSYS APDL?

10 May 2022 1 1K Report

Hi every one ;

I modeled a reinforcement concrete cylinder on ANSYS APDL, I can not extract this view which is in the file below, here someone who measures APDL can tell me how to get this view.

Kindly regards.

Alaa Elsisi

You can generate a surface and then map the result you need on it.

Badges
Science topic

Similar topics
Filing

More Ramdane Amrouche's questions See All

Bond stiffness Between Concrete and steel bar?

Hi Everyone; Can any one tell how we calculate the bond stiffness between steel and concrete, not Bond stree but Bond stiffness. and I wan to understand this formulation about Bond Stifness if...

24 February 2024 5,964 3 View

How plot the stress Bond between reinforcing concrete and steel ?

Hi ; How I can plot the bond stress between the reinforcing concrete and steel, I use the CONTACT 178 elements in the bond and in the other example the COMBINE 39. You find the file below. Best...

17 October 2021 8,556 3 View

How create interface between concrete and ribar?

Hi; Can someone help me to create this geometry in ANSYS APDL, the issue is how can I embed the length of rebar in a cube or cylinder of concrete? You found the file below about what I mean? Best...

09 October 2021 6,413 3 View

Modeling the Bond between steel and concrete?

Hi; Can Someone give me a publication about the nonlinear behavior of concrete materials using approach Willam and Warnke, 1975. Because I can't understand how I chose the exact value for the...

27 July 2021 2,119 3 View

How I can refine the mesh in this region ?

I have two solid, concrete and steel and I want to refine the zone adjacent to the steel,much finer close to the reinforcement. The problem in the file one, and I want to obtain the mush like in...

09 July 2021 6,802 2 View

How I can coincid nodes between reiforcing steel and concrete cylider I can't do it?

I can not make the coincidences between the nodes of the bar and the concrete so that I can do a pull-out test?

15 June 2021 1,319 5 View

How can I age sandstone cores?

Hi all, I would like to conduct few experiments on sandstone cores, and I need advice about ageing and which model oil should I use? Kind regards Farida

28 June 2019 4,566 11 View

Range of acid number?

Hi everyone, Would you please advise what is the range of AN in oil? Kind regards, Farida

07 September 2018 3,021 2 View

Converting from Smoluchowski ZP to ZP?

Hi everyone; Would you please advise me how to convert from Smoluchowski ZP to normal zeta potential? Kind regards,

03 September 2018 9,812 6 View

Empirical modeling of mass transfer phenomena ?

What is the difference between a model that simulates the experimental points directly and another that requires the introduction of the kinetic parameters boundaries

11 March 2017 9,190 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

Zero pivot in Abaqus concrete 3D printing simulation using model change?

Recently I've been working on a simulation of concrete 3D printing, and has successfully simulated a layer-by-layer 3D printing process using model change. However, when I proceeded to try...

06 July 2024 2,130 0 View

What heavy aggregates are available for protective concrete in your country?

01 July 2024 1,624 3 View