How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

How to remove the species data from rda data frame in R (only remain the sites/samples point)?

Dear everyone, When I using the rda function in r, I met this question. As you can see in the figure, there are a lot of deep blue points which refers to the species. But I would like remain...

15 February 2021 8,982 2 View

How to compare two group with small sample size (n=3)?

I am working on some physiological traits of plant to which its expensive to raise the sample size beyond n=3. so kindly suggest some test which is applicable to test such group(2)

04 February 2021 461 11 View

How to simulate enzymatic hydrolyis of sucrose in a CSTR coupled with ultrafiltration membrane with comsol?

Dear all, I am trying to simulate the enzymatic hydrolysis of sucrose with invertase in CSTR in Comsol. The reaction pathway is such that Sucrose + Water -> Fructose + Glucose. It is desired...

27 January 2021 2,525 4 View

How to design an Ultrafiltration membrane for a CSTR?

Dear all, I am designing an Ultrafiltration (UF) membrane coupled with a CSTR. It is desired to utilized a dead end stirred reactor. The main purpose is to separate the enzyme used from the final...

27 January 2021 7,924 1 View

Where can I find these two papers?

14 January 2021 1,572 3 View

After CRISPR and single-colony picking, cells reverted to WT?

Hi guys: I have been doing CRISPR knock-in and knock-out and one seemingly impossible scenario keeps happening. In the CRISPR knock-in attempt I tried to add a tag on a gene of interest, so I...

07 January 2021 190 3 View

I would like. How they can be simulated the deformational processes of valvular aortic stents??

We have a projet about TAVI

22 December 2020 7,729 1 View

Is there any ingredient I an add into formula to slow down gas generation from Vitamin C?

I know Vitamin C is unstable and tends to be oxidized quickly. The problem here is I made a Vitamin C beverage at pH 4-5, and it starts to generate gas in the packaging, especially at high...

13 December 2020 6,055 1 View

What is the significance of Per-Patient and Per-Tooth analysis in epidemiology?

Research in prevalence usually provide results in per-tooth/object level and per-patient level. What is the significance of these two values and which is actually more important/accurate? What are...

10 December 2020 4,248 4 View

Research on Supply Chain Management in Indian context?

Hi, I am planning to apply for the PhD degree in the Supply Chain Mgt. with specific area of "Cold Storage warehouses" during Pandemics and wars. Where lock downs and shut downs are frequent....

02 March 2021 285 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

EMSA troubleshooting. Protein-DNA complex not migrating, cold probe lane with multiple bands. Can anyone help?

I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...

24 February 2021 8,325 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View