Is it possible to create a 100-um thick polyimide layer through spin coating? If possible, What will the pi liquid's spin speed and viscosity?
Consider the impact of policy stability, corruption levels, and government efficiency on economic performance in both types of governance. Economic growth is a critical indicator of a country's...
21 June 2024 4,786 3 View
Having the thicknesses of the layer and the substrate Having the thermal diffusivity values of coated and uncoated samples
02 June 2024 5,863 1 View
I have input file for 3D material but I reduced its dimension in 3rd direction. What should be the k points for 2D.
09 May 2024 6,453 0 View
I have knowledge about monolayer of material and does not know how can I build input file and can see the structure?
01 May 2024 4,632 3 View
I want to know effect of doping on the SnO2 nanoparticles like optical properties and when using this particles as Gas sensor application
19 April 2024 6,903 2 View
Greetings, I am Mamun. I just want to know that if I use 7% margin of error than will it cause any problem in future analysis? I am using stratified sampling technique, for this if i take 7%...
06 April 2024 2,344 6 View
From the Au signal
25 February 2024 8,932 2 View
I received comments from a reviewer on my manuscript having RCT design and I compared pre and post data by pair t- test. The reviewer commented: Effect size indices and 95%CI could be...
26 January 2024 1,980 2 View
I am trying to measure Charge/Discharge curves of anode free lithium-metal battery and trying to fix both areal capacity and current density in Landbattery software. For example, areal capacity ~...
13 January 2024 3,608 1 View
let me know the antifoaming agent used in ophthalmic preparation to remove the bubbles in preparation.
25 December 2023 328 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.
09 August 2024 2,111 2 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I need to do some experiment with it in liquid form.
07 August 2024 613 3 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...
06 August 2024 4,611 0 View
I have prepared a liquid broth containing Yeast (S. Cerevisiae) that i need to add from it to fermentation media of lignocellulosic hydrolysate. I need to know based on what parameters do we add...
06 August 2024 662 1 View
I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...
02 August 2024 2,890 0 View
What is the best way to freeze the rat brain - liquid nitrogen, Dry ice , isopentane - after isolation for later protein investigation by Elisa?
01 August 2024 1,722 1 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View