How to interpret three-dimensional protein?

More Salah H. Faraj's questions See All

MAGeCK Plotting Error: Logarithmic Axis Must Have Positive Limits?

I have been running a MAGeCK test command on the terminal for a CRISPR screen to rank sgRNAs and genes based on the read count tables. However, I get only the plot of the top-ranked genes...

28 July 2024 9,811 1 View

Getting small dark current when simulating the Photovoltaic device Using the SCAPS-1D?

When I simulate the solar cell or self-power photodetector in SCAPS-1D, I optimize all parameters, Once I check the dark current at 0 voltage, the current is high in a range of (e-16-e-25), as...

06 July 2024 1,782 3 View

How to calculate Capacity retention for Lithium metal battery?

I have prepared half cell. Lithium is considered as anode in the system. Whereas, I would like to know what is actually capacity retention? How it can be calculated mathematically? On what factors...

02 June 2024 4,135 0 View

Is there a free trial of the SILVACO TCAD ?

I wan to simulate the 2D Photodetector

22 April 2024 8,756 0 View

Is there a company known that can design an electrode shadow mask for photodetector ?

I want to design electrode shadow masks for photodetectors .The shadow mask can be made from uncontaminated materials. We do not have lithography fabrication at my university, so i want to design...

12 April 2024 2,312 3 View

What is the reason that a Li-ion coin cell is not showing efficiency on neware battery testing system?

I have been working on electrospun membrane for Lithium Ion coin cells. I have tried to control different parameters, such as, thickness, electrolyte amount and many other parameters. I am facing...

26 March 2024 2,786 0 View

Is this journal legitimate (Tobacco Regulatory Science ISSN: 2333-9748 ) ?

I'm considering submitting a manuscript to this journal (Tobacco Regulatory Science ISSN: 2333-9748 ) Has anyone published in this journal before? I am looking to confirm that this journal is...

05 March 2024 4,144 1 View

What is the agricultural area using center-pivot irrigation in Egypt and how many center-pivot irrigation devices are there?

area using center-pivot irrigation in Egypt Number of center-pivot irrigation devices

16 February 2024 1,376 0 View

Is there absolute truth in marketing?

From the perspective of epistemology, is there absolute truth in marketing?

02 February 2024 9,182 6 View

Journal of Materials and Manufacturing (JMM)?

New Journal of Materials and Manufacturing (JMM): JMM is published two times per year in july and December: https://jmatman.org/index.php/journal

14 January 2024 7,729 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to solve g_mmpbsa error?

Program: g_mmpbsa, version 2024.1 Source file: extrn_apbs.cxx (line 152) Fatal error: Failed to execute command: $APBS pybYcUWA.in --output-file=pybYcUW.out

07 August 2024 6,066 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View