How to interpret the SAS output for response surface methodology using Proc RSGEG?

06 March 2018 1 534 Report

Using Proc RSGEG in SAS, the interpretation for response surface methodology when the out put is showing either maximum, minimum or saddle point, for all the three cases.

David Eugene Booth

You need a much better description of the experiment and the data set to get much assistance. David

Badges
Science topic

More Jawaid Ashraf's questions See All

Where to download DEM from 2018?

I am currently working on validating land subsidence results obtained using SBAS InSAR. Could anyone suggest reliable sources or repositories where I can download a historical DEM from 2018?...

31 July 2024 9,757 3 View

Are low quality articles included in systematic reviews and meta-analyses?

After checking the eligibility criteria, are both high-quality and low-quality articles included in the review? What is Cochrane's recommendation?

02 July 2024 5,322 4 View

Why is stiffness of structure reduced in pushover after gravity case?

So I have a structure with a pile foundation and a gravity load acting on the structure. The demand curve is drawn by running an elastic analysis. Pile-Soil is modelled as p-y, t-z, and q-z...

14 June 2024 5,220 0 View

I am trying to install gamit/globk software.After command./install_software it shows an error which is shown in below image?

PPPPlease

27 May 2024 8,219 1 View

What is the best storage method for eluted samples for Infectious Diseases panels for Molecular PCR testing?

We run Fungal Panel using Molecular PCR Technique. We extract Nuclease Free water in the same way as we extract the sample. This eluted NFW is used as negative control on our PCR Plate for quality...

16 April 2024 776 1 View

In ELISA work, If I forgot to add stop solution. And I took the absorbance. Is there a way to adjust readings as if stop solution was added?

I have read somewhere that absorbance without stop solution is about half those with stop solution. Is this true?

14 March 2024 5,575 3 View

How to remove the preprint from researchgate?

Please, I urgently need to remove and delete this article preprint "Cytotoxicity and genotoxicity reveal the link between acute cadmium exposure and Alzheimer’s disease" from Researchgate. I can't...

13 March 2024 8,002 2 View

Floating Point Exception Ansys Fluent?

I am working on Battery Pack Thermal Analysis for an Electric Vehicle. Whenever I get to the point of pressing "Run Calculation", the solver displays 1 iteration only then displays some info and...

11 February 2024 3,981 1 View

Is there any special method or software for designing random experiments?

Similar to what we typically do with CCD, but in a randomized manner!

04 February 2024 3,597 2 View

How do we change the fluorescence intensity of the confocal microscopy to quantitative result by image J?

15 January 2024 2,953 3 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,177 1 View

How can I interpret the data without the need of solving it manually?

How can I interpret the data gathered without solving?

03 August 2024 9,054 3 View

SAS Generalized Linear Model for trial/event anaysis and not survival (time to event) analysis?

I am looking for a published article using SAS or SPSS Generalized linear model for trial/event data and not survival analysis. Both software packages off the option for the number of success out...

30 July 2024 3,835 2 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

Are the apoptotic cells is positive for γH2AX ?

It has been documented that apoptotic cells themselves can induce phosphorylation of serine 139 on H2AX (γH2AX) due to DNA fragmentation during apoptosis (doi: 10.1074/jbc.275.13.9390). As γH2AX...

28 July 2024 7,983 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 647 3 View

Why only alpha wave of brain are found in some patients?

I have found an EEG where only alpha waves are present. Beta waves are not found in active patients. What interpretations ?

26 July 2024 4,741 1 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

How to interpret results of AST for Pseudomonas aeruginosa?

While doing AST for Pseudomonas aeruginosa, after incubation, no zone of inhibition observed in the plate near the well. wells surrounded by bacterial growth, when the same plate observed under UV...

25 July 2024 9,229 1 View