17 February 2021 1 8K Report

How to give an ac current to a circular coil of 10 turns made of copper wires? how to know the maximum current the coil supports?

i want to give around 50 to 100mA current and frequency 10khz.

More Shilpa Susan George's questions See All
How to plot displacement versus induced voltage in COMSOL?

I have a square planar coil of 12 turns placed on one side of the block. A ring carrying a current of 1A,1kHz is placed. I want the plot of displacement of the ring in the z-direction (height of...

16 February 2020 3,451 1 View

How to plot displacement versus induced voltage in COMSOL?

I have a square planar coil of 12 turns placed on one side of the block. A ring carrying a current of 1A,1kHz is placed. I want the plot of displacement of the ring in the z-direction (height of...

01 February 2020 775 1 View

Similar questions and discussions
Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Addition of EDTA during the synthesis of copper nanoparticles to prevent it from being oxidized?

I've attempted to use this method to synthesize copper nanoparticles. Copper nanoparticles can be synthesised using a variety of precursor materials. CuSO4, distilled water, NaOH, and EDTA are...

28 July 2024 8,027 3 View

How to achieve optimal bonding strength at the wire-bonding process?

Hello everyone, without going too much into details, my thesis is about improving the bonding strength at the wire bonding process. I should focus on laser pretreatment of the substrate. Has...

17 June 2024 366 1 View

If silver is doped to copper indium sulphide during hydrothermal synthesis by repacing some amount of copper, what will be the size of nanoparticle ?

If I dope silver during the synthesis of copper indium sulphide nanoparticles by hydrothermal method what will be the size of nanoparticles?

13 June 2024 6,844 3 View

What is the reason for the non-monotonic variation of roughness for sputtered Cu films annealed at 100, 200 and 300 degree Celsius?

I have prepared Copper thin films by magnetron sputtering and the samples have been annealed at 100, 200 and 300 degree celsius. The variation of the rms roughness and all other AFM height related...

11 June 2024 9,774 1 View

Fluid flow through copper tube?

What does it mean meshed wall and shell conduction with or without run-out method use to meshing copper tube in Ansys fluent?

07 June 2024 9,030 3 View

How can I simulate magnetic field of a wire in Cst suite learning edition?

Recently I have an assignment about Simulating magnetic field and I will need the result to derive it. But when i downloaded it i noticed that i am just a new to Simulation software. So can anyone...

04 June 2024 1,270 0 View

I want determine Iron by spectrophotometer? Anyone know about the spectrophotometric determination of iron and copper, kindly share the procedure?

spectrophotometric determination of iron and copper

04 June 2024 1,720 0 View

Is there any model/equation to predict the erosion of SS pipes due to flowing water?

I am trying to design a heat removal system for a specific application. As the heat flux is very high, the only way to reduce the temperature is by increasing fluid(water) velocity. I am worried...

27 May 2024 3,804 4 View

What are the effects of the copper wire diameter used in a DC electromagnet winding on the winding temperature that occurs during operation ?

Let's consider two windings containing thin diameter wire(0.3 mm) and thick diameter wire(4 mm). These windings operate under the following conditions. 1- The same power is applied. 2- They have...

22 May 2024 7,255 5 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close