How to get the output for shell thickness using ABAQUS software for deep drawing simulation?

09 March 2023 0 7K Report

I have used Abaqus software for deep drawing process. How to get formed sheet thickness in output.

Badges
Science topic

More Mehul Ardeshana's questions See All

How can I view the absorption peaks of highly diluted suspension liquids?

I had synthesized MoS2 nanosheets by the help of liquid phase exfoliation using probe sonication. The solvent used was a 50/50(vol%) of IPA/DI water mixture. Pre-processing of the sample was...

30 January 2019 5,593 5 View

Biasing circuit for varactor/pin diode in reconfigurable antenna?

I need to know abt biasing ckt for varactor and PIN diodes to be used in reconfigurable microstrip filter. I have seen ckt given in datasheet. It seems it is having more inductor and capacitors...

06 December 2018 5,768 5 View

In Coupled line or in hairpin Band pass filter, how to keep line width of the resonator based on the value of Zoe and Zoo?

In Coupled line or in hairpin Band pass filter, how to keep line width of the resonator based on the value of Zoe and Zoo? I mean what is use Zoe and Zoe. Do we have to take sqrt(Zoe*Zoo) and find...

01 July 2018 4,502 1 View

Natural frequency of a cantilever in underwater environment obtained is a comlex number. How can i obtained the numeric value of natural frequency?

In comsol i have created underwater environment using pressure acoustic is it the right way to do so?

07 April 2018 7,869 3 View

How to simulate combustion in diesel engine?

I tried to simulate combustion in a Diesel engine with FLUENT. I want to determine combustion characteristics in compression ignition (CI) engine and parameter such as in-cylinder pressure,...

29 August 2017 10,018 5 View

Can anyone let me know the value of Hansen solubility parameter for poly-L-lysine or L-Lysine?

I am working on self-assembly of triblock copolymer in aqua-organic mixed solution. I want to know the value (experimental/theoratical/computational calculated) of Hansen solubility parameter for...

04 May 2017 4,443 2 View

How to apply Load ratio (R ) zero for the cyclic loading in the Abaqus?

I am trying to apply cyclic loading on the cell model of cast iron. I need to apply load ratio zero. I have tried to do the same using Amplitude tool in the Load module, using periodic amplitude...

02 February 2017 4,107 3 View

How to separate α & ß isomers of steroid molecules by TLC?

05 August 2016 8,174 2 View

Is there any significant difference in numerical simulation results between 2D & 3D geometry for steady state heat transfer problem?

I want to evaluate performance of heat spreading capacity of copper heat spreader. In which silicone chip (Source) is connected with Copper plate (Sink). I had simulate problem with steady state...

29 April 2016 9,396 3 View

Are there any cloud simulators (Open Source) other than cloud sim which can simulate Cloud Environment?

I am looking for more cloud simulators which are open source and provide extended services as in cloud Sim.

09 March 2016 3,827 7 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Why reactivity isn't increased with more empty spots in valence shell?

If from a geometric perspective the non-halogens, non-noble gases have more empty spots in their valence shell, and the filling/exiting of any of the empty spots in the shell constitutes a...

03 August 2024 4,787 2 View

How to draw the five chelate rings of [Co(EDTA)]- on this picture?

Is this circle one of the rings?

03 August 2024 5,988 0 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

How to make overlapping p-h diagram in EES?

I want to draw ph diagram using Engineering equation solver EES for refrigerant R134a and R1234fy and some other. I don't know how to draw the multiple ph diagram on same dome or overlapping to...

30 July 2024 647 7 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View