Can anybody please tell me how to generate nam ou xgraph files for leach protocol(I'm using ns-2.35) ?
setup output nam file.
set nam_1 open[.....]
#ns_ nametrace-all-wireless .......
or use newer version of MANNASIM...
I suggests the same thing, using the Mannasim .
For showing the detailed steps for integrate the mannasim on NS-2.35 you can see this:
http://installwithme.blogspot.com/2014/05/how-to-integrate-mannasim-with-ns-2.35.html
A new cell subtype was found out only during regeneration phases after a cuprizone-induced demyelination model. How can I characterize this cell? It is important to highlight that was already...
13 February 2021 1,245 1 View
I need to preserve termite samples for future quantification of juvenile hormone in their bodies. Or extract the Juvenile Hormone and keep that samples stored for future quantification. I may need...
09 February 2021 1,995 1 View
31 January 2021 6,354 2 View
Instead of appearing one single correlation of the signal of the carbon at 20.9 ppm (#11 in the attached figure), aligned to hydrogen at 2.29 ppm, it appeared two correlations (2,32 and 2,26 ppm)....
16 January 2021 4,774 2 View
In the paper A wavelet-based method for power-line interference removal i... we propose a new method for removing PLI. This method consists in identifying the ECG and noise frequency range for...
29 December 2020 9,233 3 View
Have you done or thought about doing an article about the impact of covid 19 in your research / work area? If so, which one?
27 December 2020 3,777 12 View
I would like to simulate the Lorentz Force resulting from the magnetohydrodynamics (MHD) phenomenon in an ionic solution.
19 December 2020 8,278 9 View
10 December 2020 7,922 4 View
Hi Mr. Waugh! I'm using your code for JavaProp Automation for MATLAB on my thesis. How can I correctly reference it? Thank you!
09 December 2020 8,316 1 View
I am currently looking for parameters to know if 87Sr/86Sr data is reliable for chemostratigrahy in marbles, and/or parameters to know if those marbles have had some post-depositional...
30 November 2020 9,032 8 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...
01 March 2021 9,701 5 View
Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...
01 March 2021 2,327 1 View
I have designed a 24 GHz rectangular antenna on HFSS 3D model and got desired results while desing the same antenna with same dimensions I am getting resonance frequency at 27 GHz I am...
28 February 2021 4,426 2 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?
25 February 2021 9,761 1 View
Does data from contact tracing help in establishing patterns of behavior and social interactions that lead to infections? There are cases here in the Philippines where patients have no travel...
25 February 2021 9,002 13 View
I am currently working on gene clustering based on co-expression pattern in mouse brain. The problem is I do not have some solid way to test my result. Are there any suggestions for databases...
22 February 2021 4,374 3 View
For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...
21 February 2021 7,624 3 View
I have a massive of x, y, z coordinates of 2D surface in 3D space, which builded in Ansys HFSS or AutoCAD. How can I get the analitical aproximation of this surface by formulas?
21 February 2021 3,444 7 View