•ρxy=[(Vxy/Ixx).A]/L
•A=sample cross section area
•L=length in the direction of voltage terminals
is it correct?
Dear Dr Beg ---
How do you calculate Hall resistivity?Hall Calculations
VE = V13P - V13N, and VF = V31P - V31N. The sample type is determined from the polarity of the voltage sum VC + VD + VE + VF. If this sum is positive (negative), the sample is p-type (n-type).
For more on this have a look at:
https://www.nist.gov/pml/nanoscale-device-characterization-division/popular-links/hall-effect/resistivity-and-hall
kindly take a look at the following useful link:
http://courses.washington.edu/phys431/hall_effect/hall_effect.pdf
Regards--
Respected Ijaz Sahab,
this is my first time to encounter this problem to calculate hall resistivity of magnetic film.
I was thinking to use this formulae:
•ρxy=[(Vy/Ix).A]/L
•L=length in the direction (in between) of voltage terminals
And thank you for the links, i will check them thoroughly.
Ijaz Durrani
Dear Dr Beg Yes it is correct!!
Dear Researchers I need to know, how to load and plot 2D-PIV (particle image velocimetry) recorded velocity vector field data in Tecplot? Thank You
02 August 2024 3,615 1 View
The absorbance peak in the UV graph represents the electronic transition in the material when expose to light. Any material has a specific optical band gap when it must show h single peak in a UV...
28 March 2023 8,255 3 View
1. How we find out the Refractive index value (n, k) of hydrogenated amorphous silicon (a-Si:H) and nc-SiO𝑥:H(n)/a-Si:H(i) for Simulation in FDTD Lumerical. 2. How we make irregular triangle...
21 March 2023 9,890 0 View
I was using blood collection tubes without additives to extract serum samples from whole blood without complain.. but recently is started using collection tubes without additives by Junnou brand....
16 February 2023 2,238 0 View
I am simulating organic Solar cells in the FDTD Lumerical software How to find out the refractive index 3D sample data (ITO, PEDOT: PSS, PH3T: PCBM, nc-ZnO, Al). How can I check the material...
11 February 2023 6,333 2 View
I am simulating optical simulation of perovskite/Si tandem solar cells using FDTD I need to add the Material in the Lumerical FDTD . How can I add in the Material in Lumerical FDTD
16 January 2023 4,202 2 View
Respected members, I am doing a study on Co, Cr, V and Ni based medium entropy alloys (i.e. NiCoCr, NiCoV and NiCoVCr) which are single phase FCC (confirmed through XRD). While doing the XPS...
07 December 2022 440 0 View
I have to obtain an empirical equation of efficiency (E) in percentage. After applying the Buckingham-Pi theorem to the variables on which efficiency depends, I got the following non-dimensional...
18 September 2022 1,100 6 View
I received my sequence data for the plasmid with my gene of interest, and when i am trying to get annotation, my forward primer plasmid does have four mismatches with the gene of interest, and the...
13 June 2022 5,774 4 View
Hi everyone I want to test the electrocatalytic activity (Overall potential at 10 mA/cm2 and long-term stability) of my Bifunctional electrodes in a two-electrode system which means that I have...
18 March 2022 7,574 5 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View
Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...
06 August 2024 666 4 View
Air moisture harvesting Air water collection devices
06 August 2024 5,473 2 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?
31 July 2024 4,835 3 View
Are both ways acceptable, or is there any convention to them? Thanks.
22 July 2024 6,988 4 View
Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...
22 July 2024 868 0 View
When testing devices based on ITO/ZnO/CsPbBr3/TFB/MoO3/Ag structures, I found that the current density of the device always increases sharply to 1000mA/cm2 at about 3V bias, and the device does...
16 July 2024 4,291 0 View