Dear researchers,
i am looking for equation to find the natural frequency for fixed thick glass. please suggest
Hello Nouman Rafiq , take a look: https://www.researchgate.net/publication/283196636_The_response_of_a_window_glass_to_the_frequencies_of_sound
I hope it helps you out!
REgards.
Dear Mateus,
Thanks for your answer, i have already read out this paper. but i am looking for formulation so that i can calculate the values in my case.
I have been trying to perform Blue-Native PAGE using procedure from doi:10.1038/nprot.2006.62. However, the stacking gel does not solidifies even after two hours, at room temperature. Can...
04 April 2019 4,777 2 View
The Gel has pH 8.9. and the pH of loading dye is 6.67. What should be the pH of running buffer to allow smooth running of my protein into the gel. I prepared buffer of pH 8.49 but I was unable to...
25 March 2019 9,877 6 View
I submitted a manuscript on a novel and interesting finding on July 30, 2018 to a reputed journal. Following editorial review it went to peer-review. It is over 8 months, no decision yet. What...
24 March 2019 9,737 2 View
is this is because i have used monohydrate instead of anhydrous? or any other reason plz any one help
03 February 2018 1,596 1 View
someone mentioned that heat it at 78 degree Celsius, is this is the only thing to do or something else? plz anyone tell me the proper method.
03 February 2018 9,039 3 View
How can i isolate a particular region in my periodic domain and gather the data inside that small region using ansys fluent?
01 December 2015 6,180 1 View
I would like to write my research plan for my PhD on this topic.
21 April 2015 4,301 3 View
Increased value of invertebrates - Mediating variable
08 April 2015 2,834 5 View
I want to estimate the percent of oil present in mustard seed.
24 March 2015 2,233 7 View
05 February 2015 9,648 7 View
I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...
01 March 2021 395 3 View
How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...
01 March 2021 2,294 3 View
Hi there! I regularly receive suggestion about papers and authors that are totally out of my area. Does anybody know how I can fix this? Thank you!
01 March 2021 9,574 4 View
Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !
01 March 2021 2,501 3 View
I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...
27 February 2021 6,801 3 View
I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium
24 February 2021 1,915 1 View
I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...
23 February 2021 6,043 1 View
I have a fixed sample and would like to use the murexide reaction to test for uric acid composition. I no longer have fresh samples
22 February 2021 1,328 1 View
Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...
22 February 2021 3,680 4 View
I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.
21 February 2021 5,465 4 View