How to estimate parameter of Trivariate Archimedean and Meta-Elliptical copulas in MATLAB?

30 June 2021 0 8K Report

I want to estimate parameters of Trivariate Archimedean and Meta-elliptical copulas in Matlab? If anyone can help with the code?

Badges
Science topic

Similar topics
Engineering
Modeling

More Palash Kumar Pradhan's questions See All

Adding isopropanol directly to eluted RNA samples?

I have my RNA samples eluted in nuclease-free water. But now I want to store it for a longer period. Can I add isopropanol directly to my samples to store it without doing a second round of TriZol...

23 June 2024 2,576 4 View

Are the silica films hydrophilic or hydrophobic? Furthermore, what is the obtained water contact angle of silica films?

I want to know about water contact angle of silica films without using any surfactants.

29 May 2024 4,526 3 View

For hexaferrite material,what is the resistance range for becoming current at 5-20mA at constant voltage difference 1v in electrochemical measurement?

supercapacitor application

13 May 2024 5,612 1 View

After DOS calculation in material studio software, where can I found the fermi energy value?

I was not very familiar with material studio software. I have run the DOS calculation, but I can not find the Fermi energy in the DOS output file. I have to do the Fermi energy level correction...

20 April 2024 8,223 0 View

Why is the entropy during compression decreasing?

While conducting experiment following data were obtained Compressor inlet pressure : 120kPa Compressor inlet temperature: 29°C Compressor outlet temp:1000kPa Compressor outlet temperature: 66°C

07 April 2024 3,045 4 View

Any help in removing contaminating protein (possibly chaperone)?

I am trying to purify this eukaryotic protein (mol wt 60 kDa) in Rosetta strain. It is getting expressed in good quantity. However, there is another stubborn host protein (mol wt around 70 kDa)...

01 April 2024 3,961 3 View

Suggestions to improve a manuscript on Bibliometric Analysis?

Hi. I had written a manuscript on Bibliometric Analysis related to oral cancer last year. Since then I had sent it to multiple journals only to get rejected. I request you all to please give me...

04 March 2024 2,924 5 View

Can a COP of vapor compression refrigeration system be greater than 10?

I along with my friends have been doing experimental analysis on VCRs by adding heat before and after compressor for our fourth year project. We have been observing that COP of our system is...

20 February 2024 6,133 1 View

For liquid liquid extraction of phenolic compound from water solution of phenol, which solvent should be best option?

I want to analyze degradation intermediates of phenolic compound through GC-MS analysis which I had carried out in aqueous solution. For liq-liq extraction of phenolic compound from aqueous...

25 December 2023 1,205 4 View

I haver synthesized cDNA from plant RNA samples. Then I did PCR where I got nice bands. But there is no amplification in qRT-PCR using same cDNA. why?

I have synthesized cDNA using one microgram RNA template. Then, I diluted it to five times. Then, I did PCR using diluted cDNA with housekeeping gene act2. In PCR, I got nice bands in the gel....

27 September 2023 8,098 4 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Request Python code?

Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!

08 August 2024 6,242 2 View

Why does everyone use vs code?

Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...

07 August 2024 7,013 4 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Is an invitation to join the editorial board of Clinical Cardiology Updates a scam?

I received an e-mail invitation to join the editorial board of Clinical Cardiology Updates. While I have published a few articles related to cardiovascular disease, there are lots of colleagues...

06 August 2024 8,981 8 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

How can i do multivariate Time Series forecast using MLP, ANFIS and LSTM?

I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.

05 August 2024 2,977 3 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

Why 3 replicates for most biological assays? Is it enough to examine the data fits normal distribution?

Just bounced on me. Before statistically analysing significant difference, shouldn't we see if data fits normal distribution first? Is 3 replicates enough to testify the hypothesis of normal...

31 July 2024 8,141 13 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View