01 January 1970 0 2K Report

The simple and easy methods used for drawing the multiphase flow in a card.

More Adel Oueslati's questions See All
What are the publishers who publish free charges books after peer review?

Dear colleagues, I would like know publishers who publish books free charges after peer review. With my best regards!

11 December 2018 7,486 1 View

Does documents published by Lambert edito are peer reviewed?

Dear Colleagues, I would like know if the documents (Books, papers, ..) publsihed by LAMBERT editor are peer reviewed? With best regards!

11 December 2018 4,110 12 View

-What are industrial predictive control applications? Give examples?

-What are industrial predictive control applications? Give examples?

08 September 2018 6,616 3 View

What are the main processes used in paper industry?

What are the main processes used for making paper (all kinds)? How paper is recycled?

06 July 2018 9,465 6 View

How to calculate the sample size from the batch size?

how to calculate the sample size from the batch size?For the different sampling cases.

06 July 2018 3,296 0 View

What is the sampling theory?

sampling theory? what is the relationship between sample size and uncertainty about this size? Is there a table giving lot size, sample size, acceptance criteria, rejection criteria and...

06 July 2018 8,435 0 View

Patents for sale?

Dear Sir, I have several patents to put into operation. The results are guaranteed. From this fact, I would like a cooperation with a university or a research laboratory or an industrial or...

05 June 2018 3,595 5 View

What is the index of the air? How can we calculate it?

What is the index of the air? How can we calculate it?

01 February 2018 6,601 6 View

What is the water index? How can we calculate it?

What is the water index? How can we calculate it?

01 February 2018 1,503 7 View

Is there a complete air analysis protocol?

Is there a complete air analysis protocol? I need to perform a complete analysis of the air (whatever its internal or external origin). That is to say for each parameter (for example: O2, CO2,...

31 December 2017 1,010 3 View

Similar questions and discussions
Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close