Looking for method to draw an equivalent circuit using cst or ads .
Thanks Abid
Use ADS software.
Thanks sir
You can use the AppCad Design tool.
Hi Zeeshan,
by CST... from CST Home environment, choose Schematic, here u can design it by dragging the desired components.
Best wishes
I am trying to perform homology modeling using the swiss-model but I have found that the swiss-model gives the same number of residues as that of the template. Whereas my sequence has more...
21 January 2021 5,568 3 View
I want to know chemical properties such as repellent tendency.
05 January 2021 4,797 3 View
Hello I am using C-CNF in DI water and dip a flat polymer in the solution to form CNF coatings on the polymer. since DLVO didnt account for size and shape of the molecules to cause forces flat...
21 November 2020 2,308 4 View
Is it possible to observe ion pairing (contact ion or solvent separated ion) of polyelectrolyte complexes through liquid FTIR? Although the PECs have been widely studied in the last two decades, I...
12 November 2020 4,800 1 View
I want to measure the charge on the particles in the solutions using zetasizer, but the experiment needs R.I and absorbance co-efficient to be conducted, but i cant find the stated valued for the...
08 November 2020 3,691 9 View
I used TEM equipped with tungsten gun to obtain attached image (several other too, like shown). Side blotting technique followed by negative staining (1% PTA for 30 sec) was used. I cannot get the...
31 October 2020 1,902 5 View
How Carpooling will reduce Traffic Congestion? I am researching on this in Islamabad. What will be methodology to find out facts & figure? Can any one suggest best software or Survey link...
13 October 2020 8,777 8 View
i am new rearch student i want to know which topic i have to choose for research and why ? i like to chose any heterocylic compound or any of the natural product i-e phytochemicals etc.
04 October 2020 8,299 3 View
I wanted to simulate a handover algorithm for ad hoc networks, I want to know what are freely available supporting tools for academic research?
28 September 2020 4,604 7 View
Is there any software that helps us in the calculating Safe bearing capacity of the soil, permissible loads on the foundation without actually going the same calculations again and again?
25 September 2020 7,645 10 View
My study consists simple corrosion inhibitors in salty brine. Right now I just fit my circuit with randles with CPE. Just wondering how the slop can given more info of the experiment. Or any...
01 March 2021 6,474 3 View
I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...
01 March 2021 9,701 5 View
Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...
28 February 2021 2,116 1 View
Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...
28 February 2021 7,016 1 View
I have designed a 24 GHz rectangular antenna on HFSS 3D model and got desired results while desing the same antenna with same dimensions I am getting resonance frequency at 27 GHz I am...
28 February 2021 4,426 2 View
I have a doubt on how to select the inductor and capacitor value when I want to implement MPPT controller. This is because we always take a maximum output voltage and current but in this case, we...
28 February 2021 3,637 2 View
28 February 2021 5,433 3 View
Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...
27 February 2021 7,710 4 View
I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...
27 February 2021 4,218 7 View
I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?
27 February 2021 8,179 1 View