We are looking to find out the anti-fouling coating materials for stainless steel , which should remain stable at temperature around 200 degree C.
Dear Sir, You have already answered your question, however, if you want to know about the conditions/parameters please mention those also
we have few papers ready for submission, and we need one co-author for each article who can pay article fee. Interested authors may text here or contact me on my following email id [email protected]
29 July 2024 6,626 0 View
through origin software
17 July 2024 4,991 0 View
Hi, my research involves in ZnO synthesis. I have performed rietveld refinement of my samples and obtain a good fit using Fullprof suite software. However to obtain the crystallite size, the IRF...
07 July 2024 3,526 3 View
AI has the potential to improve the management of sleep apnea by personalizing treatment, enhancing diagnostic accuracy, and advancing our understanding of the condition.
03 July 2024 9,393 2 View
we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...
30 June 2024 5,943 2 View
Respected researcher, I want to know that is there any way or one can help in generating a 2D/3D image using the energy count spectrum of from backscatter methods. How can I design such an...
29 June 2024 10,023 1 View
I do a research about Non-Verbal Communication: Gestures and Body Language in Classroom.
18 June 2024 8,737 1 View
In my XPS spectral, i detected oxygen group bonded to carbon and in my zinc spectral (note : my sample is ZnO) ...there are two valent zinc species available, (which is unsual as my previous...
17 June 2024 3,888 2 View
Action research design is Quantitative Studies or Qualitative Studies?
14 June 2024 1,684 1 View
Hi there! I was wondering how I should go about interpreting the following data. I am currently investigating the moderating role of working memory (continuous) on the relationship between...
07 June 2024 1,473 0 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View