How to do EMT simulation in off grid operation using DIgSILENT?

24 July 2022 0 10K Report

The off-grid system was modeled using the dig-silent. Storage and PV were modeled as microgrids. EMT simulation is not possible because there is no synchronous generator or slacks, so BESS is not initialized. How do we solve this problem?

Badges
Science topic

More Jang Jiyeon's questions See All

Chemical storage conditions about Oleic acid and Triethylamine ?

1. Oleic acid Oleic acid is classified in a long chain acid. Should we keep in the acid storage cabinet? or keep in the general storage cabinet? which one would like to recommend? 2....

03 February 2024 452 1 View

What is suitable as an antisolvent for acetonitrile solvent?

25 July 2023 7,032 2 View

How to calculate the quantity of dopant material?

I want to experiment Zn-doped-CuI by dissolving each powder (ZnI2, CuI) in acetonitrile with different at% (0.5,10,15) so, how can I find this quantity of dopant material. concentraion of basic...

20 July 2023 7,697 0 View

What solvents is SnI4 soluble in?

What solvents is SnI4 soluble in? Is SnI4 soluble in acetonitrile?

02 July 2023 5,619 3 View

How the modification of surface treated by hmds?

Hello, I'd like to use UV to modify the surface with HMDS applied, but I have a few questions. 1. I'd like to know the surface modification wavelength band that HMDS responds to (I heard it's...

23 June 2023 7,630 0 View

What happens to the precursor if the aging time is excessive?

It was confirmed that the uniformity of the thin film increases when the solution precursor is aged and deposited. By the way, what happens if the precursor is over-aged?

18 June 2023 8,441 1 View

What is the aging split method?

We are going to conduct an experiment to compare the aging effect by manufacturing TFT after precursor aging. After 0 day, 1 day, 2 day, aging, I want to make a device and compare the...

13 June 2023 6,301 0 View

What equipment exposes at 172nm intensity?

Hello, I'm a student currently studying patterning. I would like to pattern using HMDS only without PR. After reading the previous papers, if you expose it to 172nm strength, HMDS is patterned,...

06 June 2023 4,757 0 View

How to treat Ar plasma treatment using ACP system?

I want to proceed with Ar Plasma treatment using ACP etcher for the element, what should I do in this case?

30 May 2023 5,080 0 View

How to do Ar treatment using sputter?

I would like to do Ar plasma treatment to the TFT device where Al2O3 is passivated. Now, we have a sputter in our lab that we use to deposit electrodes, and I want to use it to do only Ar plasma...

27 May 2023 6,449 1 View

Smart grid ideas?

How to use and this is economical?

06 August 2024 3,160 2 View

Element deletion problem in ABAQUS/Explicit solver using Cohesive elements?

I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...

23 July 2024 10,032 0 View

Why my mesh independent fastener as beam cartesian type not working in abaqus?

i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...

02 July 2024 6,293 0 View

Is it appropriate to use ARDL(autoregressive distributed lag model) with environmental Kuznets curve?

The underlying idea behind the environmental Kuznets curve is that GDP per capita initially increases environmental degradation but later reduces the environmental degradation as the result of the...

28 June 2024 949 0 View

Convergence problems using opensees and specifically openseespy, what algorithm and system should i use to avoid convergence problems ?

hi im performing IDA for a 30 story consisting of bearing wall system of special shear walls for gravity and lateral resisting system , i usually face convergence problems with that , the walls...

27 June 2024 9,492 0 View

How to form the state space model of SMIB with Power Electronic Load?

I am working on a small signal stability analysis of a power system on a power electronic load. The power electronic load is modeled as a voltage-dependent load and has the relation attached in...

26 June 2024 2,496 1 View

How to solve this error while I simulate gidl using tcad ?

There is an error message "interface silicon/oxide not found in grid xxx.tdr file"

26 June 2024 5,551 0 View

Can you help me the optimization micro grid using multi-objective?

Optimal sizing microgrid off grid case study ''I choose the case study""so in our research using PV and WT .battery storage and diesel generator .we have the data formation Hourly the solar ir and...

20 June 2024 5,086 0 View

How can i access papers on distributed generations and their impact?

The impact im looking for could be both positive and negative on the electric grid

18 June 2024 9,269 3 View

How can i create the swatmf_link.txt ?

Hello! I need your help. I'm trying to link SWAT-MODFLOW model i creating hru_dhru.txt, dhru_grid.txt, grid_dhru.txt, and river_grid.txt files but i don't know the steps for Create the swatmf...

15 June 2024 2,799 0 View