How do we differentiate the loading and doping in a semiconductor?
Loading is related to etching process, while doping is related to controlled substitution of atoms in a host material with other atoms. For 'loading', perhaps you wish to consult the book whose link I provide below.
http://books.google.co.uk/books?id=LmD21C80oHEC&printsec=frontcover#v=onepage&q&f=true
My qualifying exams are the next week and my university library is out of copies! I would greatly appreciate your help.
06 January 2021 9,929 1 View
I'm doing a PCR with Q5 enzyme. I would like to know how Q5 GC enhancer works so that I can decide whether to add it or not.
11 February 2019 7,083 7 View
Hi..I am working on battery aging control in EV using PSO technique ...Right now I am aiming to reduce the simulation time and make the make the code efficient ..Can some suggest me how can I...
02 November 2017 4,860 3 View
I have a QIAquick spin column but do not have the PB and PE buffers provided with it. I do know however that the binding buffer needs to have a chaotropic salt. Is there any buffer/solution with...
04 June 2017 1,750 2 View
Hi, I would like to hear suggestions about choosing cell lines for screening of small molecules. I understand that the common cell line used is MDAMB231. I also notice that use of MDAMB435 is...
09 February 2016 6,043 3 View
06 August 2015 2,210 5 View
I have recorded the UV-absorption spectrum of my sample (bismuth titanate). I wish to know how we can determine the exact bandgap based on the tauc plot, if the absorption coefficient is unknown?
18 January 2015 2,901 3 View
See above
29 October 2014 8,909 3 View
According to my knowledge, I knew that by varying the sample concentration one can vary the intensity of the PL emission, but in my sample, the PL emission wavelength keeps varying by changing the...
01 January 1970 7,738 4 View
01 January 1970 2,496 5 View
I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...
03 March 2021 1,931 5 View
I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...
02 March 2021 1,408 1 View
In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?
01 March 2021 1,923 3 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...
25 February 2021 8,749 6 View
It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...
24 February 2021 5,974 4 View
I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...
23 February 2021 9,592 2 View
Does the absorption coefficient of the semiconductor changes with the change in the structure of the semiconductor? If you have a thin film and nanowire of the same semiconductor, will the...
23 February 2021 9,799 4 View
I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...
17 February 2021 8,104 4 View