Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

Regarding to presentation of pairwise comparison of data?

22 January 2021 8,648 1 View

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

Can a luenberger observer (even a modified version) be effective for a nonlinear affine system?

I want to know whether a luenberger observer or a modified form of it be effective for estimating the states of a system of the following forms: 1. x_dot = f(x,u,d); y = x 2. x_dot = f(x,u); y =...

20 December 2020 1,392 4 View

How much Tensile strength and hardness can be acheived in Aluminium 7050 MMC with B4C reinforcement?

I have conducted research on characterisation of Al7050 + B4C by electromagnetic stir casting. The alloy employed in the process is casted alloy and the Composite too is casted. How much strength...

16 November 2020 9,226 3 View

Why whitefly prefer not to infest Pigeonpea?

Whitefly, Bemisia tabaci is pest of broad host range. In pulse crops, it generally infests greengram, blackgram and cowpea but not Pigeonpea. There might be some biochemical or morphological...

09 November 2020 9,199 3 View

Can u suggest how to identify the matrix material and reinforcement particle distribution in the MMC of scanning electron miroscopy (SEM) images?

How to identify the reinforcement particle behavior in SEM images

09 November 2020 8,664 3 View

Can someone help me in designing off-MPPT mode in a Standalone DC Microgrid?

I am working on voltage control of a Standalone DC Microgrid consisting of Single PV source, a battery and loads. The PV is interfaced through Buck converter to the DC bus, the battery is...

01 October 2020 7,071 2 View

Modeling pure shear loads in Abaqus?

I am trying to simulate a pure shear loading on a cubical block with a single brick element. While I am simulating the other stress components are not getting zeros. Can anyone suggest to me how...

22 September 2020 7,649 3 View

Can anyone suggest any introductory book on tensor analysis and tensor calculus for continuum mechanics?

I have searched google. But it would be more helpful to get suggestions from personal experience.

14 September 2020 5,426 5 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

Please suggest a good text book for "Research Methodology in Life Sciences". Which book would be good for PhD Scholars?

Please provide Book Title and author name

02 March 2021 9,059 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Why does intensity drops as concentration increases?

Is there any reason for decrease in fluorescence emission intensity of HSA,BSA when increase the concentration ?

28 February 2021 3,653 4 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View