How to determine the concentration of gas (PPM) in a specific area for the purpose of calculating sensitivity of gas sensor?
DEAR SIR,
The attached chapter may be helpfull.
Rami.
DEAR SIR, helpful
Hi Ausama, please see the link, https://www.researchgate.net/post/How_do_I_calculate_the_gas_concentration_in_PPM
The following equation might be helpful.
ppm=(volume of gas/volume of chamber)*concentration (ppm) in cylinder
Hi Ausama,
For calculations, if you are using 1 gas molecule in a specific area, if you can find the volume of the gas molecule, you can use the following:
ppm = (volume of the molecule)/(volume of the area)
I need software of Original Lab, May help me ?
14 October 2020 142 3 View
How determined the dose rate of gamma rays cobalt (60Co)as source with an activity of 6 mCi and doses levels of 0, 50, 100 and 200 Gy, ? How does this dose rate then apply for thin films?
22 July 2019 6,174 2 View
21 July 2017 4,380 3 View
How can characterize the semiconductor materials of metal oxide when coated by MOF (Metal-Organic Frameworks)?
21 April 2017 3,393 1 View
how can we characterize the semiconductor materials of metal oxide when coated by MOF (Metal-Organic Frameworks) ?
20 April 2017 8,776 1 View
What is meaning of reduction of graphene oxide?
06 April 2017 884 2 View
I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...
28 February 2021 6,477 1 View
I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...
27 February 2021 8,128 1 View
Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...
26 February 2021 6,253 3 View
I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...
26 February 2021 1,511 3 View
Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...
26 February 2021 1,100 5 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View
Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...
21 February 2021 2,333 4 View
My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...
18 February 2021 9,928 2 View
Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...
17 February 2021 1,578 4 View
Our team is designing a smart water C&C dashboard for a smart city initiative. As we look into the current smart water system landscape, we couldn't reconcile to a definitive solution that...
16 February 2021 1,094 3 View