How to couple Structural Mechanics and Electrostats?

12 March 2024 0 10K Report

Hi, I'm working on a project in COMSOL 6.1 in which I have to use Electrostats and Solid Mechanics as a coupled physics, for which I have used Electromechanics Multiphysics.

But, when I run the simulation, the solid mechanics gets executed but the Electrostats doesn't. I can see and analyse deformation but i can't see any changes in model due to Electrostats.

Badges
Science topic

More Apoorv Krishan's questions See All

How to produce ROC/AUC curve using various groundwater vulnerability method for comparative analysis?

ROC/AUC Vulnerability Groundwater Machine learning

11 October 2020 9,186 3 View

Is taking coffee and tea without milk beneficial for our health?

Consumption of tea and coffee without milk is considered beneficial for our health. Can you please explain the reasons behind it? what can be other methods for improving sensory characteristics...

14 May 2020 6,096 23 View

What to do for the markers showing negative position on a linkage group in a join map ?

1. I am creating linkage groups in citrus using Joinmap and few of the markers show negative position during mapping (otherwise linked), should we omit such markers? 2. If two or more markers are...

02 March 2020 1,372 1 View

Can anyone suggest what are these large bubble like structure along with small organoids and how to get rid of them?see the attached image.?

I am growing 3D organoids from mouse lung AT2 cells in matrigel. I am using glutamine, Penstrep. 10% FBS, ITS and tGF b inhibitor in media.after 6 days I observe large bubble like structure in the...

02 January 2020 1,352 5 View

What is Spatial auto-correlation in ecology, when it good to consider and when it should be avoided?

auto correlation is daunting for early career researcher, what is limit to say something is auto correlated [

16 December 2019 6,303 3 View

Will Fluorescent polymers will not show Raman spectra?

I have synthesized a fluorescent polymer. But when i am taking its raman spectra it is not showing any peak. Does it have anything to do with fluorescent property of my compound/ or fluorescence...

30 August 2019 8,328 6 View

What is the exact representation of space group of Kesterite Cu2ZnSnS4?

Kesterite Cu2ZnSnS4 have space group I-4. There is a problem in the representation of Zn and Sn atoms position in 2c and 2d plane in I-4 space group by the software...

09 May 2019 4,735 1 View

The non-stoichiometric condition/ Cu poor Zn rich condition is beneficial for high efficiency of the solar cell in CZTS/Se?

The non-stoichiometric condition/ Cu poor Zn rich condition is beneficial for high efficiency of the solar cell, but also formed the undesirable defects. These undesirable defects are CuZn+ZnCu,...

14 November 2018 1,537 3 View

How to prepare mucin containing medium?

Hi, I am working on mucin utilizing microorganisms and for this I need to prepare a medium for the same. I have encountered with the following a) Using porcine stomach (type II) mucin, is there...

20 August 2018 8,668 11 View

How to optimize the processing time for different foods in Retort Pouching machine?

In retort pouching system, How we can optimize the process time for different food formulations/mixes.

24 July 2018 5,453 1 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View