How to convert the received signal SNR to the correct reception Rate?

02 February 2018 1 2K Report

I read in some papers that there is a relationship between the received signal SNR and the delivery rate or the rate of the correctly received packets, So I hope you can help me with a reference for that or the specific relationship.

Mustafa Aljumaily

Thanks so much Dr. Monyer

Badges
Science topic

Similar topics
Correction

More Mustafa Aljumaily's questions See All

Data sets for Beamforming?

Is there any publicly available data set to work on for massive MIMO Hybrid Beamforming?

01 February 2019 7,607 2 View

What are the expected extensions in the journal paper that was already published in a conference?

Many conferences mention in their call for papers that the authors of accepted papers in the conference will be invited to submit an extended version of the paper to be published in "xxx" journals...

02 March 2018 2,867 3 View

What is the best simulator to implement new routing protocol in MANET networks?

What is the best network simulator to implement new routing protocol for mobile ad hoc networks that support directional antennas and beamforming?

02 March 2018 9,571 12 View

Is there any direct relationship between Path loss and Probability of Delivery or Delivery Rate?

in Mobile wireless networks, is there an equation that connects the path loss for specific modulation and coding scheme (MCS) and specific distance between Tx and Rx with the packet delivery ratio...

01 February 2018 3,612 3 View

What is the Maximum Transmission power of UE in wireless networks?

This reference [1] says that "The maximum EIRP is regulated to be 43 dBm for mobile stations (MSs) by the FCC" which means about 20 watt. But normal simulators are usually using less than 10 watt...

01 February 2018 6,230 12 View

How much usually does it take for your publications to begin getting citations especially if they have been read and downloaded tens of times?

This question has been asked by many researchers and I liked to share it with my colleagues to get some ideas.

01 January 1970 9,882 13 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View