How to change transmission range of nodes in dsdv-manet in ns3.Can anyone help me with the code?

More Moshfika Ikfath's questions See All

Can anyone help me in calculating performance metrics like delay,routing overhead,energy consumption,etc from ns3 for dsdv routing protocols?

I am working in wireless sensor network. I have to calculate performance metrices for dsdv routing protocols using ns3.I have used dsdv-manet source file for calcultaing thoughput,but for other...

11 December 2018 1,302 5 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

The Shannon's index is inversely proportional to Simpson's index (1-D)?

I'm having a problem with my bloxplot with Shannon's and Simpson's indexs. The value of Shannon for my Community 1 indicating higher diversity (in relation of the Community 2), but have lower...

26 February 2021 3,033 9 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

What is difference between In-line transmission (%) and Total transmission (%) value of optically transparent Ceramics?

I am working on transparent/translucent zirconia-based ceramics. In many papers, I have seen that they are reporting both In-line transmission (%) & Total transmission (%) value of...

20 February 2021 9,405 6 View

Specify the Burgers vectors for dislocations, which cannot be uniquely identified.?

1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...

20 February 2021 2,370 1 View

Akram H. Jebril

Hi Moshfika,

If you are talking about the range transmission of LoRa nodes, it can be changed by increase the spreading factor (SF). Whenever we increase the SF the range will be increased too. However, the bite rate will be reduced.

Chandra Shekhar

Moshfika Ikfath

I am not aware about dsdv-manet.how model but transmission range can be increased by increasing the transmitting power level. You need to change the default power level. However you can also change the SF.