No title

08 September 2017 941 5 View

Is it possible to determine hydroxyl value by 859 Trioterm? If yes, how ? If no, what is the alternative for this determination?

I search an accurate method for determiantion hydroxyl value in Hydroxy acrylic resin, saturated polyester resin and alkyd resin.

15 March 2017 2,038 3 View

Is it possible to determine hydroxyl value by 859 Trioterm? If yes, how ? If no, what is the alternative for this determination?

I search an accurate method for determiantion hydroxyl value in Hydroxy acrylic resin, saturated polyester resin and alkyd resin.

02 March 2017 7,079 3 View

Can anyone support me with reference or paper about reactivity ratio of acrylate monomers in hydroxy acrylic, TPA and TSA solvent born?

Reactivity ratio of monomer in polymerization reaction

11 December 2015 9,383 1 View

What are the keys for reading an IR chart for Acrylic polymer Solvent borne, saturated polyester and adhesive flexible packaging?

How can i read IR chart ?

10 November 2015 6,215 6 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View