How to calculate Tafel for OER?

Noorulain Babar @Noorulain-Babar

19 January 2018 1 9K Report

Thank you in Advance.

Noorulain Babar

Thank you very much Sir, for verifying. Yes its a mistake. Value of slope is 126.9 mV/dec.

Badges
Science method

More Noorulain Babar's questions See All

What does skewness and kurtosis in construction management refer to and what are permissible limits of these in civil engineering with references?

The question is about assessment of skewness and kurtosis to carryout a research in construction management through SPSS software. The purpose behind the question is to know the permissible values...

12 November 2020 7,114 3 View

How to calculate Reactance of a transmission line?

I'm working on Simulink MATLAB. I have values of Voltage and Current on busses and I want to calculate the Reactance of transmission line between these two busses. Is there any block available in...

14 February 2020 7,624 2 View

How to calculate Power Loss in Simulink MATLAB?

If someone has any model of simulation in which power loss is calculated or anything helping material please suggest. I have it in code form but want to implement it on any distributed system in...

05 February 2020 9,905 4 View

How much time is required to Sonicate the mixture of GO-SiO2 Nanoparticles in Water/Ethanol base to make nanofluid?

I want to prepare nanofluid using GO-SiO2 in water. I want to know about best duration in which NPs completly dispersed in base.

30 September 2019 2,503 3 View

Does anyone know how to passivate the SU-8 surface against the oil used for the objective?

14 April 2019 9,928 2 View

What statistic tools can be used on camera trap data?

I collectd data by using camera trap on a wild animal. It consisted at 130 photos. I have placed data in Excel with multiple columns of image no., year, month, date, time, temperature, lunar...

26 May 2018 8,511 9 View

How to select potential for Electrochemical Impedance???

Dear All, I want to calculate the electrochemical impedance of electrolyte-electrocatalyst interphase using Autolab. I am confused how to select the overpotential or potential vs Ag/AgCl. In a...

04 May 2018 4,015 9 View

How to calculate Electrochemically active surface area and RF? What is specific current density how to calculate it?

I am working on Thin Film materials. I want to calculate ECSA (cm2) , by double layer capacitance using CV mode. First i need to identify non-faradaic region (somewhere in between the hydrogen and...

14 January 2018 9,008 12 View

How much time International Journal of Control (T&F) take from submitting article to publish on web?

I need to submit a paper to International Journal of Control (T&F). but I am wondering how much time it will take to respond you back and then (if paper got accepted) how much time to publish...

23 October 2017 4,416 3 View

Why there is shift of potential to a more + value with increasing concentration?

I am working on electrochemical sensing of metals, SCE is reference electrode Pt wire as CE and GCE modified with Au-NPs as WE. As+3 is detected and oxidized at 167-220 mV vs. SCE but at very low...

21 February 2017 5,099 6 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

Runs of nucleotides in Sanger sequencing?

I performed site directed mutagenesis, transformation, and then I sent out plasmids for Sanger sequencing and found out that there is extension of DNA just before the stop codon. I am not sure...

27 February 2021 547 3 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

Calculating volume of DNA required from DNA concentration?

Hi I am a bit confused. They are asking me to find out the volume of DNA required in ul (a total of 30-100 ng for genomic DNA) from the DNA concentration in the nanodrop reading which was 404.8...

26 February 2021 5,029 2 View

Could not amplify CD28 and CD3z ectodomain from cDNA of Jurkat Cells ?

For my experiments, I have to express ectodomains of human CD28 and CD3z. As a source, I extracted RNA from Jurkat cells and verified the quality of RNA on the gel. I, then, prepared cDNA using...

23 February 2021 7,051 4 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

What effect does the large temperature difference between the two primers have on PCR, including real time PCR?

What effect does the large temperature difference between the two primers have on PCR, including real time PCR? If I did not get a result from real time PCR, is it possible that my problems are...

21 February 2021 4,094 7 View