Hi,
I am doing in vitro reaction with recombinant substrate protein and kinase. We got the activity of the kinase, 16nmol/min/mg, how much substrate protein and kinase should I use? And how much should the total volume of reaction be?
Thanks,
Ran
Hi, I searched vaccination study to know which MLD50 is suitable for influenza virus study in pubmed. But why every vaccination and challenge conditions are different? Is there no guideline or...
16 January 2021 7,984 3 View
Actually, I want to present the in table form (dcal , dexp, 2 thita, hkl) but don't know how to find these values from data.
28 December 2020 6,769 4 View
As Cronbach's Alpha is usually used for test the reliability of measurements given by questionnaires, however, I wonder that whether I use this test for features extracted from behavioral data. I...
26 December 2020 9,602 2 View
if the percentage of doping Au into rGO is too small 1~10%, is it not enough to prevent restacking of r-GO in xrd results, rGO peak appeared at 22.2 and also the peaks of gold nanoparticles so...
21 December 2020 6,091 3 View
is the concentration of gold salt that were added will affect on the peaks appeared. i added a very little amount of gold salt to dope graphene oxide and not all the peaks that proved the...
17 December 2020 9,275 3 View
14 December 2020 5,935 3 View
i am trying to dope boron in graphene oxide , and after i take out my samples from the oven i put them in the microwave for 40 sec , and i saw sparkles . and fume also i couldn't understand why
16 November 2020 6,852 5 View
08 November 2020 3,249 2 View
I received this gastric tumor biopsis and processed using standard protocol to establish gastric cancer organoids. Contamination looks like this. I have never seen this before and the culture...
08 November 2020 8,541 4 View
Recently I have been working in some embankment project and plaxis V20 is the FEM software I am using to calculate. But by the time I am working, I figured out the water load sometimes applied to...
27 October 2020 7,835 1 View
Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,
02 March 2021 0 0 View
Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...
02 March 2021 3,024 2 View
I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...
01 March 2021 8,544 1 View
Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...
28 February 2021 3,442 2 View
The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...
28 February 2021 6,560 14 View
Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...
25 February 2021 3,443 4 View
I'm currently working having problem with the concentration for recombinant protein use in western blot, the one been used is Recombinant Human CD19 Fc Chimera Protein-rndsystem which does not...
24 February 2021 8,514 3 View
My purpose is to recognize the volatility clustering property without statistical tests such as The Lagrange Multiplier (LM) test.
24 February 2021 4,150 3 View
My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...
22 February 2021 2,125 3 View
22 February 2021 9,932 11 View