How to calculate abortion of material????

31 January 2017 1 1K Report

now i am doing my project based on the abortion of materiel (that material like sand witch modal that means three materials in three layers, i want individual absorption of materials), how to calculate scattering of light, problem is i am doing nano meter range, i want accurate absorption of light in material,excluding scattering losses

F.A. Abdel-Wahab

your point is not clear

Badges
Science topic

More Satya prakash Mugada's questions See All

Can anyone please help me in processing SAR SLC data to generate interferogram using SNAP?

I have two scenes of the study area, one top and the other bottom. As per the tutorials and papers published, the step include coregistering the master sand slave images. However, when i try to...

24 February 2021 6,372 1 View

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

Can a luenberger observer (even a modified version) be effective for a nonlinear affine system?

I want to know whether a luenberger observer or a modified form of it be effective for estimating the states of a system of the following forms: 1. x_dot = f(x,u,d); y = x 2. x_dot = f(x,u); y =...

20 December 2020 1,392 4 View

Can someone help me in designing off-MPPT mode in a Standalone DC Microgrid?

I am working on voltage control of a Standalone DC Microgrid consisting of Single PV source, a battery and loads. The PV is interfaced through Buck converter to the DC bus, the battery is...

01 October 2020 7,071 2 View

How to do simulation of Wood polymer composites in ANSYS?

I need a detailed explanation on how to add materials since it has two different materials. And step by step procedure and which module to be used for perfect simulation

07 September 2020 7,885 3 View

How do you dissolve polyethyelene terephthalate (PET)?

I want do dissolve about 225g of PET. So I want to know the quantity of solvent to be used.

03 August 2020 507 3 View

How to scale the time frame of battery operation in MATLAB?

How can we make the rating of a battery in MATLAB/Simulink to Amp-sec instead of Amp-hour? I have tried with reducing the factor of 3600 to 1 inside the battery block. Is this approach completely...

03 July 2020 4,017 4 View

Can someone suggest me a good resource to get the information on design of Adaptive controllers like Model Reference Adaptive Control in MATLAB?

Please suggest me a good source to learn the design of adaptive controllers like MRAC. Resources related to the implementation on MATLAB platform and for Power electronic converter systems would...

01 May 2020 7,422 3 View

How to use bandpass filter with timeseries data?

How to use bandpass filter (say 30-60 day) with daily timeseries data (for 365 days) especially in MATLAB? How many data points are going to be reduced after filtering? Any suggestion would be...

12 December 2019 7,182 5 View

What are the data requirements for PCSWMM modeling?

What are the data required to simulate the Urban Flood scenario for an Urban catchment using PCSWMM? Further for model calibration and validation of what necessary information needed?

10 November 2019 6,025 3 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

How can I make stacked bar graph with scatter plot?

I want to make a stacked bar graph with showing each data value as dots. I tried with graph pad prism, version 6, but could not succeed. Does anyone have tried before making such graphs?

01 March 2021 9,383 1 View