Which is the best coating method to coat nano sheets of graphene on a plane copper surface?
Dear Dr. James Andrew Whitby
Thank you very much for your answer. If I heat the copper surface to 150 degree centigrade after coating, what is the possibility that the coating will not come out of the surface?
Many thanks for your answer. I want separate nano particles on the surface instead of continuous covering. I will try it and see how it works.
Hello everyone, I have written a narrative review on a topic obtaining the literature from other research articles and review papers. But I wish to convert it to systematic review (without meta...
07 July 2024 6,105 5 View
Kindly reply
26 August 2022 352 2 View
What instrument can be used to measure the electricity generation from solar panel throughout the day?
03 February 2020 9,994 3 View
I want to know what is going to happen to the hollow iron pipe if it is used in concrete? It will get compressed?
02 August 2018 6,940 5 View
What the easiest method remove nitrogen from air? How the composition of air can be determined experimentally?
02 August 2018 4,127 4 View
Has any one used moxonidine for ADHD? How does it compare with clonidine?
06 July 2017 9,356 0 View
Is it possible to do machining operations on solid graphite? What about its weldability?
15 June 2017 7,811 4 View
PCM can act like a thermal storage material. But where PCM coupled at the evaporator of the heat pipe can be used?
07 June 2017 684 3 View
Anyone knows how the voltage fluctuations can be incorporated into experimental uncertainty?
25 May 2017 3,542 4 View
Can anyone suggest the models for phytoremediation of heavy metals, especially for rhizofiltration, phytoextraction and phytostabilization?
16 February 2015 5,373 4 View
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
i am unable to interpret why its increases in start as shown in figure
11 August 2024 2,179 1 View
"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....
10 August 2024 8,621 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...
10 August 2024 8,992 0 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...
08 August 2024 6,134 12 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
For example, I perform passivation process before electropolymerization of Py for adhesion to titanium surface. Is a similar or different procedure required for ITO? If necessary, I would be glad...
06 August 2024 3,176 0 View