PCM can act like a thermal storage material. But where PCM coupled at the evaporator of the heat pipe can be used?
Dear Mukul Ray
I have seen a few articles on PCM-Heat pipe. A few researchers have applied PCM at evaporator. What will be the possible applications of that set up?
Dear Trijo Tharayil
See this article, "Evacuated tube solar collectors integrated with phase change materials" https://doi.org/10.1016/j.solener.2015.12.040.
Good luck
Mr. Adel A. Eidan
Thanks for the paper. Solar water heating is one the application for my question because PCM can store heat which can be used at night to get hot water. Any other applications???
Hello everyone, I have written a narrative review on a topic obtaining the literature from other research articles and review papers. But I wish to convert it to systematic review (without meta...
07 July 2024 6,105 5 View
Kindly reply
26 August 2022 352 2 View
What instrument can be used to measure the electricity generation from solar panel throughout the day?
03 February 2020 9,994 3 View
I want to know what is going to happen to the hollow iron pipe if it is used in concrete? It will get compressed?
02 August 2018 6,940 5 View
What the easiest method remove nitrogen from air? How the composition of air can be determined experimentally?
02 August 2018 4,127 4 View
Has any one used moxonidine for ADHD? How does it compare with clonidine?
06 July 2017 9,356 0 View
Is it possible to do machining operations on solid graphite? What about its weldability?
15 June 2017 7,811 4 View
Anyone knows how the voltage fluctuations can be incorporated into experimental uncertainty?
25 May 2017 3,542 4 View
Can anyone suggest the models for phytoremediation of heavy metals, especially for rhizofiltration, phytoextraction and phytostabilization?
16 February 2015 5,373 4 View
.
01 August 2013 6,973 21 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View
I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...
28 July 2024 4,006 2 View
I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....
24 July 2024 4,058 5 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...
15 July 2024 9,065 4 View
Heat transfer
06 July 2024 2,134 1 View